Add Malyan 3d printer variants

boards.txt

@@ -724,6 +724,34 @@ RAK.menu.upload_method.STLink.upload.tool=stlink_upload
 3dprinter.menu.pnum.REMRAM_V1.build.variant=REMRAM_V1
 3dprinter.menu.pnum.REMRAM_V1.build.cmsis_lib_gcc=arm_cortexM7l_math
 
+# MALYANM200_F103CB board
+# Support: Serial2 (USART2 on PA3, PA2)
+3dprinter.menu.pnum.MALYANM200_F103CB=Malyan M200 V1
+3dprinter.menu.pnum.MALYANM200_F103CB.upload.maximum_data_size=20480
+3dprinter.menu.pnum.MALYANM200_F103CB.upload.maximum_data_size=122880
+3dprinter.menu.pnum.MALYANM200_F103CB.build.mcu=cortex-m3
+3dprinter.menu.pnum.MALYANM200_F103CB.build.board=MALYANM200_F103CB
+3dprinter.menu.pnum.MALYANM200_F103CB.build.series=STM32F1xx
+3dprinter.menu.pnum.MALYANM200_F103CB.build.product_line=STM32F103xB
+3dprinter.menu.pnum.MALYANM200_F103CB.build.variant=MALYANM200_F103CB
+3dprinter.menu.pnum.MALYANM200_F103CB.build.cmsis_lib_gcc=arm_cortexM3l_math
+3dprinter.menu.pnum.MALYANM200_F103CB.build.startup_file=-DCUSTOM_STARTUP_FILE
+3dprinter.menu.pnum.MALYANM200_F103CB.build.extra_flags=-D{build.product_line} {build.enable_usb} {build.xSerial} -DVECT_TAB_OFFSET=0x2000
+
+# MALYANM200_F070CB board
+# Support: Serial2 (USART2 on PA3, PA2)
+3dprinter.menu.pnum.MALYANM200_F070CB=Malyan M200 V2
+3dprinter.menu.pnum.MALYANM200_F070CB.upload.maximum_data_size=20480
+3dprinter.menu.pnum.MALYANM200_F070CB.upload.maximum_data_size=122880
+3dprinter.menu.pnum.MALYANM200_F070CB.build.mcu=cortex-m0
+3dprinter.menu.pnum.MALYANM200_F070CB.build.board=MALYANM200_F070CB
+3dprinter.menu.pnum.MALYANM200_F070CB.build.series=STM32F0xx
+3dprinter.menu.pnum.MALYANM200_F070CB.build.product_line=STM32F070xB
+3dprinter.menu.pnum.MALYANM200_F070CB.build.variant=MALYANM200_F070CB
+3dprinter.menu.pnum.MALYANM200_F070CB.build.cmsis_lib_gcc=arm_cortexM0l_math
+3dprinter.menu.pnum.MALYANM200_F070CB.build.startup_file=-DCUSTOM_STARTUP_FILE
+3dprinter.menu.pnum.MALYANM200_F070CB.build.extra_flags=-D{build.product_line} {build.enable_usb} {build.xSerial} -DVECT_TAB_OFFSET=0x2000
+
 # RUMBA32 board
 3dprinter.menu.pnum.RUMBA32=RUMBA32
 3dprinter.menu.pnum.RUMBA32.upload.maximum_size=524288
@@ -735,6 +763,34 @@ RAK.menu.upload_method.STLink.upload.tool=stlink_upload
 3dprinter.menu.pnum.RUMBA32.build.variant=RUMBA32_F446VE
 3dprinter.menu.pnum.RUMBA32.build.cmsis_lib_gcc=arm_cortexM4l_math
 
+# MALYANM200_F103CB board
+# Support: Serial2 (USART2 on PA3, PA2)
+3dprinter.menu.pnum.MALYANM200_F103CB=Malyan M200 V1
+3dprinter.menu.pnum.MALYANM200_F103CB.upload.maximum_data_size=20480
+3dprinter.menu.pnum.MALYANM200_F103CB.upload.maximum_data_size=122880
+3dprinter.menu.pnum.MALYANM200_F103CB.build.mcu=cortex-m3
+3dprinter.menu.pnum.MALYANM200_F103CB.build.board=MALYANM200_F103CB
+3dprinter.menu.pnum.MALYANM200_F103CB.build.series=STM32F1xx
+3dprinter.menu.pnum.MALYANM200_F103CB.build.product_line=STM32F103xB
+3dprinter.menu.pnum.MALYANM200_F103CB.build.variant=MALYANM200_F103CB
+3dprinter.menu.pnum.MALYANM200_F103CB.build.cmsis_lib_gcc=arm_cortexM3l_math
+3dprinter.menu.pnum.MALYANM200_F103CB.build.startup_file=-DCUSTOM_STARTUP_FILE
+3dprinter.menu.pnum.MALYANM200_F103CB.build.extra_flags=-D{build.product_line} {build.enable_usb} {build.xSerial} -DVECT_TAB_OFFSET=0x2000
+
+# MALYANM200_F070CB board
+# Support: Serial2 (USART2 on PA3, PA2)
+3dprinter.menu.pnum.MALYANM200_F070CB=Malyan M200 V2
+3dprinter.menu.pnum.MALYANM200_F070CB.upload.maximum_data_size=20480
+3dprinter.menu.pnum.MALYANM200_F070CB.upload.maximum_data_size=122880
+3dprinter.menu.pnum.MALYANM200_F070CB.build.mcu=cortex-m0
+3dprinter.menu.pnum.MALYANM200_F070CB.build.board=MALYANM200_F070CB
+3dprinter.menu.pnum.MALYANM200_F070CB.build.series=STM32F0xx
+3dprinter.menu.pnum.MALYANM200_F070CB.build.product_line=STM32F070xB
+3dprinter.menu.pnum.MALYANM200_F070CB.build.variant=MALYANM200_F070CB
+3dprinter.menu.pnum.MALYANM200_F070CB.build.cmsis_lib_gcc=arm_cortexM0l_math
+3dprinter.menu.pnum.MALYANM200_F070CB.build.startup_file=-DCUSTOM_STARTUP_FILE
+3dprinter.menu.pnum.MALYANM200_F070CB.build.extra_flags=-D{build.product_line} {build.enable_usb} {build.xSerial} -DVECT_TAB_OFFSET=0x2000
+
 # PRNTR_F407_V1 board
 # Support: Serial1 (USART1 on PA10, PA9)
 3dprinter.menu.pnum.PRNTR_F407_V1=PRNTR F407 v1

package.json

@@ -0,0 +1,7 @@
+{
+    "description":"Arduino STM32 Official Framework (stm32core)",
+    "name":"framework-arduinostm32core",
+    "system":"all",
+    "url":"https://github.com/xC0000005/Arduino_Core_STM32",
+    "version":"1.0.0"
+}

variants/MALYANM200_F070CB/PeripheralPins.c

@@ -0,0 +1,238 @@
+/*
+ *******************************************************************************
+ * Copyright (c) 2018, STMicroelectronics
+ * All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright notice,
+ *    this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright notice,
+ *    this list of conditions and the following disclaimer in the documentation
+ *    and/or other materials provided with the distribution.
+ * 3. Neither the name of STMicroelectronics nor the names of its contributors
+ *    may be used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+ * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *******************************************************************************
+ * Automatically generated from STM32F070CBTx.xml
+ */
+#include "Arduino.h"
+#include "PeripheralPins.h"
+
+/* =====
+ * Note: Commented lines are alternative possibilities which are not used per default.
+ *       If you change them, you will have to know what you do
+ * =====
+ */
+
+//*** ADC ***
+
+#ifdef HAL_ADC_MODULE_ENABLED
+const PinMap PinMap_ADC[] = {
+    {PA_0,  ADC1,  STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC_IN0
+    {PA_1,  ADC1,  STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC_IN1
+    {PA_2,  ADC1,  STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC_IN2
+    {PA_3,  ADC1,  STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC_IN3
+    {PA_4,  ADC1,  STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC_IN4
+    {PA_5,  ADC1,  STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC_IN5
+    {PA_6,  ADC1,  STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)}, // ADC_IN6
+    {PA_7,  ADC1,  STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC_IN7
+    {PB_0,  ADC1,  STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 8, 0)}, // ADC_IN8
+    {PB_1,  ADC1,  STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 9, 0)}, // ADC_IN9
+    {NC,    NP,    0}
+};
+#endif
+
+//*** DAC ***
+
+//*** No DAC ***
+
+//*** I2C ***
+
+#ifdef HAL_I2C_MODULE_ENABLED
+const PinMap PinMap_I2C_SDA[] = {
+    {PB_7,  I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF1_I2C1)},
+    {PB_9,  I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF1_I2C1)},
+    {PB_11, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF1_I2C2)},
+    {PB_14, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF5_I2C2)},
+    {NC,    NP,    0}
+};
+#endif
+
+#ifdef HAL_I2C_MODULE_ENABLED
+const PinMap PinMap_I2C_SCL[] = {
+    {PB_6,  I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF1_I2C1)},
+    {PB_8,  I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF1_I2C1)},
+    {PB_10, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF1_I2C2)},
+    {PB_13, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF5_I2C2)},
+    {NC,    NP,    0}
+};
+#endif
+
+//*** PWM ***
+
+#ifdef HAL_TIM_MODULE_ENABLED
+const PinMap PinMap_PWM[] = {
+    {PA_1,  TIM15,  STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_TIM15, 1, 1)},  // TIM15_CH1N
+    {PA_2,  TIM15,  STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_TIM15, 1, 0)},  // TIM15_CH1
+    {PA_3,  TIM15,  STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_TIM15, 2, 0)},  // TIM15_CH2
+    {PA_4,  TIM14,  STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_TIM14, 1, 0)},  // TIM14_CH1
+    {PA_6,  TIM3,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM3, 1, 0)},  // TIM3_CH1
+    {PA_6,  TIM16,  STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_TIM16, 1, 0)},  // TIM16_CH1
+    {PA_7,  TIM1,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 1, 1)},  // TIM1_CH1N
+    {PA_7,  TIM3,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM3, 2, 0)},  // TIM3_CH2
+    {PA_7,  TIM14,  STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_TIM14, 1, 0)},  // TIM14_CH1
+    {PA_7,  TIM17,  STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_TIM17, 1, 0)},  // TIM17_CH1
+    {PA_8,  TIM1,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 1, 0)},  // TIM1_CH1
+    {PA_9,  TIM1,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 2, 0)},  // TIM1_CH2
+    {PA_10, TIM1,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 3, 0)},  // TIM1_CH3
+    {PA_11, TIM1,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 4, 0)},  // TIM1_CH4
+    {PB_0,  TIM1,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 2, 1)},  // TIM1_CH2N
+    {PB_0,  TIM3,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM3, 3, 0)},  // TIM3_CH3
+    {PB_1,  TIM1,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 3, 1)},  // TIM1_CH3N
+    {PB_1,  TIM3,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM3, 4, 0)},  // TIM3_CH4
+    {PB_1,  TIM14,  STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_TIM14, 1, 0)},  // TIM14_CH1
+    {PB_4,  TIM3,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM3, 1, 0)},  // TIM3_CH1
+    {PB_5,  TIM3,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM3, 2, 0)},  // TIM3_CH2
+    {PB_6,  TIM16,  STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM16, 1, 1)},  // TIM16_CH1N
+    {PB_7,  TIM17,  STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM17, 1, 1)},  // TIM17_CH1N
+    {PB_8,  TIM16,  STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM16, 1, 0)},  // TIM16_CH1
+    {PB_9,  TIM17,  STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM17, 1, 0)},  // TIM17_CH1
+    {PB_13, TIM1,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 1, 1)},  // TIM1_CH1N
+    {PB_14, TIM1,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 2, 1)},  // TIM1_CH2N
+    {PB_14, TIM15,  STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM15, 1, 0)},  // TIM15_CH1
+    {PB_15, TIM1,   STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 3, 1)},  // TIM1_CH3N
+    {PB_15, TIM15,  STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM15, 1, 1)},  // TIM15_CH1N
+    {PB_15, TIM15,  STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM15, 2, 0)},  // TIM15_CH2
+    {NC,    NP,    0}
+};
+#endif
+
+//*** SERIAL ***
+
+#ifdef HAL_UART_MODULE_ENABLED
+const PinMap PinMap_UART_TX[] = {
+    {PA_0,  USART4,  STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART4)},
+    {PA_2,  USART2,  STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART2)},
+    {PA_9,  USART1,  STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART1)},
+    {PA_14, USART2,  STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART2)},
+    {PB_6,  USART1,  STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_USART1)},
+    {PB_10, USART3,  STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART3)},
+    {NC,    NP,    0}
+};
+#endif
+
+#ifdef HAL_UART_MODULE_ENABLED
+const PinMap PinMap_UART_RX[] = {
+    {PA_1,  USART4,  STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART4)},
+    {PA_3,  USART2,  STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART2)},
+    {PA_10, USART1,  STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART1)},
+    {PA_15, USART2,  STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART2)},
+    {PB_7,  USART1,  STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_USART1)},
+    {PB_11, USART3,  STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART3)},
+    {NC,    NP,    0}
+};
+#endif
+
+#ifdef HAL_UART_MODULE_ENABLED
+const PinMap PinMap_UART_RTS[] = {
+    {PA_1,  USART2,  STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART2)},
+    {PA_12, USART1,  STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART1)},
+    {PA_15, USART4,  STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART4)},
+    {PB_1,  USART3,  STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART3)},
+    {PB_14, USART3,  STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART3)},
+    {NC,    NP,    0}
+};
+#endif
+
+#ifdef HAL_UART_MODULE_ENABLED
+const PinMap PinMap_UART_CTS[] = {
+    {PA_0,  USART2,  STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART2)},
+    {PA_6,  USART3,  STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART3)},
+    {PA_11, USART1,  STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART1)},
+    {PB_7,  USART4,  STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART4)},
+    {PB_13, USART3,  STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART3)},
+    {NC,    NP,    0}
+};
+#endif
+
+//*** SPI ***
+
+#ifdef HAL_SPI_MODULE_ENABLED
+const PinMap PinMap_SPI_MOSI[] = {
+    {PA_7,  SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)},
+    {PB_5,  SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)},
+    {PB_15, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI2)},
+    {NC,    NP,    0}
+};
+#endif
+
+#ifdef HAL_SPI_MODULE_ENABLED
+const PinMap PinMap_SPI_MISO[] = {
+    {PA_6,  SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)},
+    {PB_4,  SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)},
+    {PB_14, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI2)},
+    {NC,    NP,    0}
+};
+#endif
+
+#ifdef HAL_SPI_MODULE_ENABLED
+const PinMap PinMap_SPI_SCLK[] = {
+    {PA_5,  SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)},
+    {PB_3,  SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)},
+    {PB_10, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
+    {PB_13, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI2)},
+    {NC,    NP,    0}
+};
+#endif
+
+#ifdef HAL_SPI_MODULE_ENABLED
+const PinMap PinMap_SPI_SSEL[] = {
+    {PA_4,  SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)},
+    {PA_15, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)},
+    {PB_9,  SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
+    {PB_12, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI2)},
+    {NC,    NP,    0}
+};
+#endif
+
+//*** CAN ***
+
+//*** No CAN_RD ***
+
+//*** No CAN_TD ***
+
+//*** ETHERNET ***
+
+//*** No Ethernet ***
+
+//*** QUADSPI ***
+
+//*** No QUADSPI ***
+
+//*** USB ***
+
+#ifdef HAL_PCD_MODULE_ENABLED
+const PinMap PinMap_USB[] = {
+  {PA_11, USB, STM_PIN_DATA(STM_MODE_INPUT, GPIO_NOPULL, 0)}, // USB_DM
+  {PA_12, USB, STM_PIN_DATA(STM_MODE_INPUT, GPIO_NOPULL, 0)}, // USB_DP
+  {PA_13, USB, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_USB)}, // USB_NOE
+  {NC,    NP,    0}
+};
+#endif
+
+//*** No USB_OTG_FS ***
+
+//*** No USB_OTG_HS ***

variants/MALYANM200_F070CB/PinNamesVar.h

@@ -0,0 +1,31 @@
+/* SYS_WKUP */
+#ifdef PWR_WAKEUP_PIN1
+SYS_WKUP1 = PA_0,
+#endif
+#ifdef PWR_WAKEUP_PIN2
+SYS_WKUP2 = PC_13,
+#endif
+#ifdef PWR_WAKEUP_PIN3
+SYS_WKUP3 = NC,
+#endif
+#ifdef PWR_WAKEUP_PIN4
+SYS_WKUP4 = PA_2,
+#endif
+#ifdef PWR_WAKEUP_PIN5
+SYS_WKUP5 = NC,
+#endif
+#ifdef PWR_WAKEUP_PIN6
+SYS_WKUP6 = PB_5,
+#endif
+#ifdef PWR_WAKEUP_PIN7
+SYS_WKUP7 = PB_15,
+#endif
+#ifdef PWR_WAKEUP_PIN8
+SYS_WKUP8 = NC,
+#endif
+/* USB */
+#ifdef USBCON
+USB_DM = PA_11,
+USB_DP = PA_12,
+USB_NOE = PA_13,
+#endif