ETH.end() crashes

[JAndrassy]

Board

ESP32 Dev Module

Device Description

Espressif Dev module

Hardware Configuration

W5500 wired to default SPI pins

Version

latest development Release Candidate (RC-X)

IDE Name

Arduino IDE

Operating System

Linix Mint

Flash frequency

80 MHz

PSRAM enabled

no

Upload speed

921600

Description

ETH.end() crashes

Sketch

#define ETH_PHY_TYPE        ETH_PHY_W5500
#define ETH_PHY_ADDR        1
#define ETH_PHY_CS          5
#define ETH_PHY_IRQ         26
#define ETH_PHY_RST         -1
#define ETH_PHY_SPI         SPI

#include <ETH.h>

void setup() {

  Serial.begin(115200);
  delay(500);

  SPI.begin();

  ETH.begin();
  while (!ETH.hasIP()) {
    Serial.print('.');
    delay(1000);
  }

  ETH.end();

  ETH.begin();
  while (!ETH.hasIP()) {
    Serial.print('.');
    delay(1000);
  }
}

void loop() {

}

Debug Message

CORRUPT HEAP: Bad tail at 0x3ffb9a00. Expected 0xbaad5678 got 0x00000000
assert failed: multi_heap_free multi_heap_poisoning.c:276 (head != NULL)

stack trace:

0x400827ad: panic_abort at /home/runner/work/esp32-arduino-lib-builder/esp32-arduino-lib-builder/esp-idf/components/esp_system/panic.c:466
0x40088709: esp_system_abort at /home/runner/work/esp32-arduino-lib-builder/esp32-arduino-lib-builder/esp-idf/components/esp_system/port/esp_system_chip.c:84
0x4008d99a: __assert_func at /home/runner/work/esp32-arduino-lib-builder/esp32-arduino-lib-builder/esp-idf/components/newlib/assert.c:81
0x4008cb25: multi_heap_free at /home/runner/work/esp32-arduino-lib-builder/esp32-arduino-lib-builder/esp-idf/components/heap/multi_heap_poisoning.c:276 (discriminator 1)
0x40083792: heap_caps_free at /home/runner/work/esp32-arduino-lib-builder/esp32-arduino-lib-builder/esp-idf/components/heap/heap_caps.c:388
0x4008d9d9: free at /home/runner/work/esp32-arduino-lib-builder/esp32-arduino-lib-builder/esp-idf/components/newlib/heap.c:39
0x4011dddd: post_instance_delete at /home/runner/work/esp32-arduino-lib-builder/esp32-arduino-lib-builder/esp-idf/components/esp_event/esp_event.c:439
 (inlined by) esp_event_loop_run at /home/runner/work/esp32-arduino-lib-builder/esp32-arduino-lib-builder/esp-idf/components/esp_event/esp_event.c:615
0x4011de40: esp_event_loop_run_task at /home/runner/work/esp32-arduino-lib-builder/esp32-arduino-lib-builder/esp-idf/components/esp_event/esp_event.c:107 (discriminator 15)

Other Steps to Reproduce

WiFi has _esp_netif = NULL; before destroyNetif();. Doing this in ETH.end() avoids the crash, but following ETH.begin() then ends with "E (8710) esp_eth: esp_eth_driver_uninstall(263): 2 ethernet reference in use".

I have checked existing issues, online documentation and the Troubleshooting Guide

• I confirm I have checked existing issues, online documentation and Troubleshooting guide.

[sirapol]

@sirapol please do not hijack my issue. your problem is different.

Ok sorry

[JAndrassy]

@me-no-dev, it forgets the static IP. I don't know if it should preserve it, since legacy Ethernet API doesn't have config, but WiFi.disconnect() does not erase the static IP configuration here and in other WiFi libraries.
and end() in other Ethernet libraries with 'config` (in esp8266 and RP2040 core) doesn't forget the static IP settings.

EDIT: and now I see that static IP config is not used if I don't have DHCP begin() first. I will add it as issue tomorrow.

[me-no-dev]

@JAndrassy please open separate issue for that. ETH is different than WiFi, so it might need different approach.

[me-no-dev]

Also in what case would it make sense to restart the network and keep the same settings, as opposed to just leave it as-is and unplug and plug wherever is necessary

[TD-er]

One example when one might want to call ETH.end() and later start over with exactly the same settings:

Ethernet does consume quite a lot of energy.
Typically 50 mA for the Ethernet chip alone and another 50 mA when the link is 'up'.

So it does make sense to power the chip down when it gets unplugged and periodically do a quick check to see if it is plugged in again.

[me-no-dev]

Because of our network model, implementing this feature will require specific workarounds, that I do not think warrant this 1 in a million use case. You have to be on ETH cable, without PoE or wall power, decide to not just pull RST of ETH and go to deep sleep and also be too bothered to add one line. BTW if you really shut down all WiFi it should also lose the address, because both WiFi netifs will be destroyed. IMHO its not worth it to implement this instead of calling config() after begin()