ESP32 BLE/WiFi throws an error [E][WiFiClient.cpp:395] write(): fail on fd 54, errno: 11, "No more processes" - still not resolved

[sudheeshsmadhav]

Board

ESP32 devkit v4

Device Description

I am using ESP32 devkit v4

Hardware Configuration

no GPIO connections, ESP32 scans the BLE tags and sends their id and rssi values over mqtt

Version

latest master

IDE Name

Platform IO also uses arduino IDE 1.8.57.0

Operating System

Windows10

Flash frequency

80MHz

PSRAM enabled

no

Upload speed

115200

Description

ESP32 scans the available BLE tags and publishing the collected information over mqtt (Raspberry Pi 4 B is the broker). It was working fine in the last month.
now it started to print error in the console something like [E][WiFiClient.cpp:395] write(): fail on fd 54, errno: 11, "No more processes" and after some time it restarts. BLE scan runs in a freeRTOS task. MQTT publishing is in loop().

it works fine for around 5min(time interval is random) then fails and reboot as the log mentioned.

[E][WiFiClient.cpp:395] write(): fail on fd 54, errno: 11, "No more processes"
[E][WiFiClient.cpp:395] write(): fail on fd 54, errno: 113, "Software caused connection abort"

Sketch

will provide if requested.

Debug Message

[E][WiFiClient.cpp:395] write(): fail on fd 54, errno: 11, "No more processes"
[E][WiFiClient.cpp:395] write(): fail on fd 54, errno: 11, "No more processes"
[E][WiFiClient.cpp:395] write(): fail on fd 54, errno: 11, "No more processes"
[E][WiFiClient.cpp:395] write(): fail on fd 54, errno: 11, "No more processes"
[E][WiFiClient.cpp:395] write(): fail on fd 54, errno: 11, "No more processes"
[E][WiFiClient.cpp:395] write(): fail on fd 54, errno: 11, "No more processes"
[E][WiFiClient.cpp:395] write(): fail on fd 54, errno: 11, "No more processes"
[E][WiFiClient.cpp:395] write(): fail on fd 54, errno: 11, "No more processes"
[E][WiFiClient.cpp:395] write(): fail on fd 54, errno: 11, "No more processes"
[E][WiFiClient.cpp:395] write(): fail on fd 54, errno: 113, "Software caused connection abort"
PUB Result: 0
number of uploads: 153

ets Jun  8 2016 00:22:57

rst:0xc (SW_CPU_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:2
load:0x3fff0018,len:4
load:0x3fff001c,len:1044
load:0x40078000,len:10124
load:0x40080400,len:5828
entry 0x400806a8

Other Steps to Reproduce

No response

I have checked existing issues, online documentation and the Troubleshooting Guide

• I confirm I have checked existing issues, online documentation and Troubleshooting guide.

[MomePP]

I also got this error but in my case, it's a Wi-Fi AP as webserver by using WiFiManager. After started webserver, ESP writing response to client. This error showing up then crash.

This only happended with latest release(2.0.2). Downgrade to 2.0.1, It works fine.

[BeaverUI]

I have exactly the same issue with my code. I use MQTT, BLE, and WiFi together on an ESP32. It runs for a while, and then resets at a quasi-random time.

@MomePP: I didn't get your comment, I believe the WiFiClient is in the board definitions file, and no version 2.0.2 there. Or am I missing something?

[sudheeshsmadhav]

I didn't use the WiFiManager. h

#include <WiFi.h>
#include <PubSubClient.h>
#include <ArduinoJson.h>
#include <ESP32Time.h>
#include <WiFiUdp.h>
#include <BLEDevice.h>
#include <BLEUtils.h>
#include <BLEScan.h>
#include <BLEAdvertisedDevice.h>

I use only these files in my code

[BeaverUI]

I have these:

#include <WiFi.h>
#include "BLEDevice.h"
#include <ESPmDNS.h>
#include <ArduinoOTA.h>
#include <MQTT.h>
#include <WiFiClient.h>

Different MQTT library, by the way.

[MomePP]

@BeaverUI

Sorry for the confusion. What I mean is version of ESP32 Arduino Core that i used and WiFiClient is part of definition file in WiFi library.

In my case i used WiFiManager library, which is based from WiFi library. So i got the same issue with WiFiClient.
However, I didn't use BLE.

[BeaverUI]

Thanks, I changed to 2.0.1 now, let's see what happens. It usually takes less than 24 hours before it throws the error.

[BeaverUI]

Oops, it did it again. Changing the Arduino Core made no difference. What I notice is that some processes seem to struggle:

• My mqtt broker sometimes gives a timeout on the connection to the ESP
• WiFi on the ESP sometimes reconnects
• BLE on the ESP sometimes throws an error
• The available heap decreases continuously, but I can't find any leaks in my code. When doing scans only, without connecting, there is no leak.
• After a while the ESP reboots or freezes, which is at a random moment but always seem to align with the moment that BLE is active.

[sudheeshsmadhav]

Hi, changed some library files and their versions. Still the issue available. Anybody identified any possible solutions? I reinstalled the Arduino ide, tried different versions of library files. No use... It is still makes me mad.

[sudheeshsmadhav]

Not a permanent solution but some how I am able to handle it. I am repeatedly sending data from esp to server, So this problem made some gap in the communication. As the error printed - [E][WiFiClient.cpp:395] write(): fail on fd 54, errno: 11, "No more processes" , I am able to point out the error code in the wificlient.cpp file. Upon printing the log, I made the ESP to restart. So ESP will get in to the active loop within few seconds rather than printing the error log in console for more than 10 seconds. But looking for a permanent solution.

[sudheeshsmadhav]

any solution for this. ?

[VojtechBartoska]

Hello all contributors, can you please retest this on v2.0.3-rc1?