esp 32 wroom MODULE current reading

[ViruKM]

Related area

AFTER DOWNLOADING ny codes like I2C, WIFI ANY CODE

Hardware specification

Support ESP32 WROOM module wifi

Is your feature request related to a problem?

after downloading the any codes unable to reading current in uA

Describe the solution you'd like

any codes examples from ESP 32 Arduino ide examples also same issue

Describe alternatives you've considered

No response

Additional context

No response

I have checked existing list of Feature requests and the Contribution Guide

• I confirm I have checked existing list of Feature requests and Contribution Guide.

[lucasssvaz]

Could you please explain your problem better and provide a minimal sketch to reproduce the issue ? How are you trying to measure the current ? Starting from 3.0.0 the HAL sensor is not supported anymore due to changes in IDF

[ViruKM]

#include "driver/periph_ctrl.h" #include "driver/spi_master.h" #include "driver/adc.h" #include "esp_sleep.h" #include "driver/gpio.h" #define SPI_SCK 18 #define SPI_MISO 19 #define SPI_MOSI 23 #define SPI_CS 5 #define ADC_PIN 36 void setup() { Serial.begin(9600); delay(100); Serial.println("Starting setup..."); periph_module_enable(PERIPH_SPI_MODULE); gpio_reset_pin((gpio_num_t)SPI_SCK); gpio_set_direction((gpio_num_t)SPI_SCK, GPIO_MODE_OUTPUT); gpio_set_level((gpio_num_t)SPI_SCK, 0); adc1_config_width(ADC_WIDTH_BIT_12); adc1_config_channel_atten(ADC1_CHANNEL_0, ADC_ATTEN_DB_11); esp_sleep_enable_timer_wakeup(10 * 10000); Serial.println("SPI clock enabled. No other peripherals are initialized.") ; } void loop() { float voltage = readVoltage(); Serial.print("Voltage: "); Serial.print(voltage); Serial.println(" V"); if (voltage < 3.0) { enterDeepSleep(); //diff power modes } else { enterLightSleep(); } delay(100); } float readVoltage() { int adcValue = adc1_get_raw(ADC1_CHANNEL_0); float voltage = adcValue * (3.6 / 4095.0); voltage *= 2; return voltage; } void enterLightSleep() { Serial.println("Entering light sleep mode..."); esp_light_sleep_start(); Serial.println("Waking up from light sleep mode..."); } void enterDeepSleep() { Serial.println("Entering deep sleep mode..."); esp_deep_sleep_start(); } void enterActiveMode() { Serial.println("Entering active mode..."); } above code downloaded in ESP 32 wifi WROOM module using Arduino IDE 2.3.2 after uploading, measuring current using multimeter in uA. it shows Overload, can you provide proper guide Thanks Viru KM

…

On Tue, Jul 30, 2024 at 7:30 PM Lucas Saavedra Vaz ***@***.***> wrote: Could you please explain your problem better and provide a minimal sketch to reproduce the issue ? How are you trying to measure the current ? Starting from 3.0.0 the HAL sensor is not supported anymore due to changes in IDF — Reply to this email directly, view it on GitHub <#10086 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/ANCZD4ZR3IKBGKHTL4XXTZDZO6L73AVCNFSM6AAAAABLWH5FPWVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDENJYGQZDKOBSGM> . You are receiving this because you authored the thread.Message ID: ***@***.***>

[lucasssvaz]

The multimeter measurement is going out of scale. Please put the multimeter in mA mode.