error: pll_cal exceeds 2ms!!!

[mkeyno]

---------------------------- Remove above -----------------------------

Basic Infos

Hardware

Hardware: ESP-12F
Core Version: last update 2.2

Description

just after soldering the fresh ESP-12F on the board and upload the helloworld example of library , its throw
error: pll_cal exceeds 2ms!!!
in every couple of second without any crash and exception, instead no connection lunched whereas serial print shows its work and gain the ip address , I've checked couple of lib example as well and also regard to this link put the wifi_set_sleep_type(NONE_SLEEP_T); inside setup but no success
is it possible the module had broken ?

Settings in IDE

Module: ?Generic ESP8266 Module?
Flash Size: ?2MB/1MB?
CPU Frequency: ?80Mhz?
Flash Mode: ?qio?
Flash Frequency: ?40Mhz?
Upload Using: ?OTA / SERIAL?
Reset Method: ?ck / nodemcu?

error: pll_cal exceeds 2ms!!!

[middelink]

This comes directly out of the SDK libphy.a, so I don't think it is an Arduino library issue. You might want to try and wipe the entire flash area, in case there is some residual settings left. Not knowing your environment I don't know how you want to do that though.

Good luck.

[mkeyno]

thanks for reply @middelink , I erase the module with this code esptool.py -p com23 erase_flash ,the error vanished but module not work neither of any AP or Station mode, do you think module is broken ? do you know any other solution ?
tnx

[middelink]

It depends entirely on your code I would say.

Did you try, say https://github.com/esp8266/Arduino/tree/master/libraries/ESP8266WebServer/examples/HelloServer (and filled in the right constant around line 6/7? If you did and it doesn't connect, yeah, you likely zapped something. And for SoftAP testing, use something like https://github.com/esp8266/Arduino/tree/master/libraries/DNSServer/examples/CaptivePortalAdvanced/CaptivePortalAdvanced.ino. Try both, nothing works? > bricked...

[mkeyno]

yes I did both of those example and I thinks its wifi bricked but its other function work well and can use for no wifi MCU chip
is it weird the one core section of MUC bricked and remain works fine?

[arsalanhassanawan]

Hi

I had the same issue and I was able to resolve it by replacing the libphy.a file (as brought into attention by @middelink) in the SDK that comes with the arduino libraries for ESP8266.
As of now, the ESP8266 arduino libraries come with SDK version 1.5.3_16_04_18. I downloaded the SDK version 2.0.0_16_08_10 from the Espressif website from here: http://bbs.espressif.com/viewtopic.php?f=46&t=2451. I replaced the old file "C:\Users\[user]\AppData\Local\Arduino15\packages\esp8266\hardware\esp8266\2.3.0\tools\sdk\lib\libphy.a" with the new one "ESP8266_NONOS_SDK_V2.0.0_16_08_10.zip\ESP8266_NONOS_SDK\lib\libphy.a". I compiled and uploaded my arduino code again and the issue was resolved! :)
Hope it helps!

[mkeyno]

@middelink , @arsalanhassanawan , I change my usb-serial cable and its work fine now , this is so odd , is not ?
also for some sketch always throw exception and serial garbage whereas with fix usb-serial module work fine
how come serial hardware links can affect on sketch ?

[middelink]

Well, actually, if you take the power from USB as well, it might be that the other cable simply has too much voltage drop @300mA peak. If you have a good scope, you can verify. Or slap a big ass capacitor on your circuit :)

[3mp3ri0r]

Hi all. To get away "error: pll_cal exceeds 2ms!!!", just let esp8266 power pin got 3.3v power before ch_pd pin. The "error: pll_cal exceeds 2ms!!!" won't bother you anymore. Hahaha.

[McMajan]

@arsalanhassanawan: thank you!!!! After 2 day of headache you solution works!!!!

[hongo2]

now trying other version of the core

[devyte]

All, the latest git is already on sdk 2.0.0, so it should be using the libphy referenced here. Please give that a try.
You should not be just replacing the libphy in a prior version of the core. The sdk 2.0.0 requires certain wifi radio calibration calls, which I believe don't exist in prior versions of the core.

@hongo2 please edit your post and add markup, the schematic isn't clear as it is.

[hongo2]

the divider didnt work at the end

[devyte]

I see that you're supplying 5V to the Vin, and then also using a resistor dividor connected on the 3.3V pin. Am I reading that right? I'm not an expert on wiring the nodemcu, but if I am reading it right, I don't think you're supposed to. Supplying 5V to Vin powers the on board regulator, which in turn gives you the 3.3V on the pin. If so, adding the resistor divider only loads the regulator output, which worsens the voltage for the ESP itself. That can mess with the wifi radio. Anyways, please report here the behavior with latest git to see if the pll_cal error is gone.

…

On Sep 16, 2017 5:13 PM, "hongo2" ***@***.***> wrote: hi @devyte <https://github.com/devyte> check this out: esp8266 nodemcu error: pll_cal exceeds 2ms!!! schematics solution [image: esp8266 nodemcu error pll_cal exceeds 2ms schematics solution] <https://user-images.githubusercontent.com/4730869/30515614-e4f280cc-9b01-11e7-80d2-8391c91d7292.png> — You are receiving this because you were mentioned. Reply to this email directly, view it on GitHub <#2566 (comment)>, or mute the thread <https://github.com/notifications/unsubscribe-auth/AQC6Bs9d823So9UvsDgqEjsZQlZD2rWVks5sjCvggaJpZM4KLDfB> .

[hongo2]

@devyte
the divider is not the solution I was using v2.3
http://arduino.esp8266.com/stable/package_esp8266com_index.json

now installed latest git version original branch,
eebc5ec

and seems to be working ok now without any hardware mods.

keep you posted, thanks