Added support for WPA2 Enterprise, including example code.

README.rst

@@ -13,7 +13,10 @@ Introduction
     :target: https://travis-ci.com/adafruit/Adafruit_CircuitPython_ESP32SPI
     :alt: Build Status
 
-CircuitPython driver library for using ESP32 as WiFi  co-processor using SPI
+CircuitPython driver library for using ESP32 as WiFi co-processor using SPI.
+The companion firmware `is available on GitHub
+<https://github.com/adafruit/nina-fw>`_. Please be sure to check the example code for
+any specific firmware version dependencies that may exist.
 
 
 Dependencies

adafruit_esp32spi/adafruit_esp32spi.py

@@ -82,6 +82,10 @@
 
 _SEND_DATA_TCP_CMD     = const(0x44)
 _GET_DATABUF_TCP_CMD   = const(0x45)
+_SET_ENT_IDENT_CMD     = const(0x4A)
+_SET_ENT_UNAME_CMD     = const(0x4B)
+_SET_ENT_PASSWD_CMD    = const(0x4C)
+_SET_ENT_ENABLE_CMD    = const(0x4F)
 
 _START_CMD             = const(0xE0)
 _END_CMD               = const(0xEE)
@@ -376,6 +380,30 @@ def wifi_set_passphrase(self, ssid, passphrase):
         if resp[0][0] != 1:
             raise RuntimeError("Failed to set passphrase")
 
+    def wifi_set_entidentity(self, ident):
+        """Sets the WPA2 Enterprise anonymous identity"""
+        resp = self._send_command_get_response(_SET_ENT_IDENT_CMD, [ident])
+        if resp[0][0] != 1:
+            raise RuntimeError("Failed to set enterprise anonymous identity")
+
+    def wifi_set_entusername(self, username):
+        """Sets the desired WPA2 Enterprise username"""
+        resp = self._send_command_get_response(_SET_ENT_UNAME_CMD, [username])
+        if resp[0][0] != 1:
+            raise RuntimeError("Failed to set enterprise username")
+
+    def wifi_set_entpassword(self, password):
+        """Sets the desired WPA2 Enterprise password"""
+        resp = self._send_command_get_response(_SET_ENT_PASSWD_CMD, [password])
+        if resp[0][0] != 1:
+            raise RuntimeError("Failed to set enterprise password")
+
+    def wifi_set_entenable(self):
+        """Enables WPA2 Enterprise mode"""
+        resp = self._send_command_get_response(_SET_ENT_ENABLE_CMD)
+        if resp[0][0] != 1:
+            raise RuntimeError("Failed to enable enterprise mode")
+
     @property
     def ssid(self):
         """The name of the access point we're connected to"""

examples/esp32spi_wpa2ent_simpletest.py

@@ -0,0 +1,90 @@
+# Example code implementing WPA2 Enterprise mode
+#
+# This code requires firmware version 1.3.0, or newer, running
+# on the ESP32 WiFi co-processor. The latest firmware, and wiring
+# info if you are using something other than a PyPortal, can be found
+# in the Adafruit Learning System:
+# https://learn.adafruit.com/adding-a-wifi-co-processor-to-circuitpython-esp8266-esp32/firmware-files#esp32-only-spi-firmware-3-8
+
+import re
+import time
+import board
+import busio
+from digitalio import DigitalInOut
+
+from adafruit_esp32spi import adafruit_esp32spi
+import adafruit_esp32spi.adafruit_esp32spi_requests as requests
+
+# Version number comparison code. Credit to gnud on stackoverflow
+# (https://stackoverflow.com/a/1714190), swapping out cmp() to
+# support Python 3.x and thus, CircuitPython
+def version_compare(version1, version2):
+    def normalize(v):
+        return [int(x) for x in re.sub(r'(\.0+)*$','', v).split(".")]
+    return (normalize(version1) > normalize(version2)) - (normalize(version1) < normalize(version2))
+
+print("ESP32 SPI WPA2 Enterprise test")
+
+# For running on the PyPortal, use this block
+esp32_cs = DigitalInOut(board.ESP_CS)
+esp32_ready = DigitalInOut(board.ESP_BUSY)
+esp32_reset = DigitalInOut(board.ESP_RESET)
+
+# For a board that doesn't have the ESP pin definitions, use this block and
+# set the pins as needed.
+#esp32_cs = DigitalInOut(board.D8)
+#esp32_ready = DigitalInOut(board.D5)
+#esp32_reset = DigitalInOut(board.D7)
+
+spi = busio.SPI(board.SCK, board.MOSI, board.MISO)
+esp = adafruit_esp32spi.ESP_SPIcontrol(spi, esp32_cs, esp32_ready, esp32_reset)
+
+requests.set_interface(esp)
+
+if esp.status == adafruit_esp32spi.WL_IDLE_STATUS:
+    print("ESP32 found and in idle mode")
+
+# Get the ESP32 fw version number, remove trailing byte off the returned bytearray
+# and then convert it to a string for prettier printing and later comparison
+firmware_version = ''.join([chr(b) for b in esp.firmware_version[:-1]])
+print("Firmware vers.", firmware_version)
+
+print("MAC addr:", [hex(i) for i in esp.MAC_address])
+
+# WPA2 Enterprise support was added in fw ver 1.3.0. Check that the ESP32
+# is running at least that version, otherwise, bail out
+assert version_compare(firmware_version, "1.3.0") >= 0, (
+    "Incorrect ESP32 firmware version; >= 1.3.0 required.")
+
+# Set up the SSID you would like to connect to
+# Note that we need to call wifi_set_network prior
+# to calling wifi_set_enable.
+esp.wifi_set_network(b'YOUR_SSID_HERE')
+
+# If your WPA2 Enterprise network requires an anonymous
+# identity to be set, you may set that here
+esp.wifi_set_entidentity(b'')
+
+# Set the WPA2 Enterprise username you'd like to use
+esp.wifi_set_entusername(b'MY_USERNAME')
+
+# Set the WPA2 Enterprise password you'd like to use
+esp.wifi_set_entpassword(b'MY_PASSWORD')
+
+# Once the network settings have been configured,
+# we need to enable WPA2 Enterprise mode on the ESP32
+esp.wifi_set_entenable()
+
+# Wait for the network to come up
+print("Connecting to AP...")
+while not esp.is_connected:
+    print(".", end = "")
+    time.sleep(2)
+
+print("")
+print("Connected to", str(esp.ssid, 'utf-8'), "\tRSSI:", esp.rssi)
+print("My IP address is", esp.pretty_ip(esp.ip_address))
+print("IP lookup adafruit.com: %s" % esp.pretty_ip(esp.get_host_by_name("adafruit.com")))
+print("Ping google.com: %d ms" % esp.ping("google.com"))
+
+print("Done!")