diff --git a/boards.txt b/boards.txt index c0f7f9f0ee..17f7ad0f88 100644 --- a/boards.txt +++ b/boards.txt @@ -1009,6 +1009,14 @@ GenF4.menu.pnum.BLACKPILL_F401CC.build.board=BLACKPILL_F401CC GenF4.menu.pnum.BLACKPILL_F401CC.build.product_line=STM32F401xC GenF4.menu.pnum.BLACKPILL_F401CC.build.variant=PILL_F401XX +# BlackPill F411CE +GenF4.menu.pnum.BLACKPILL_F411CE=BlackPill F411CE +GenF4.menu.pnum.BLACKPILL_F411CE.upload.maximum_size=524288 +GenF4.menu.pnum.BLACKPILL_F411CE.upload.maximum_data_size=131072 +GenF4.menu.pnum.BLACKPILL_F411CE.build.board=BLACKPILL_F411CE +GenF4.menu.pnum.BLACKPILL_F411CE.build.product_line=STM32F411xE +GenF4.menu.pnum.BLACKPILL_F411CE.build.variant=PILL_F411XX + # Core board F401RCT6 GenF4.menu.pnum.CoreBoard_F401RC=Core board F401RCT6 GenF4.menu.pnum.CoreBoard_F401RC.upload.maximum_size=262144 diff --git a/variants/PILL_F411XX/PeripheralPins.c b/variants/PILL_F411XX/PeripheralPins.c new file mode 100644 index 0000000000..3a54b1d4f3 --- /dev/null +++ b/variants/PILL_F411XX/PeripheralPins.c @@ -0,0 +1,211 @@ +/* + ******************************************************************************* + * Copyright (c) 2019, STMicroelectronics + * All rights reserved. + * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ******************************************************************************* + * Automatically generated from STM32F401C(B-C)Ux.xml + */ +#include "Arduino.h" +#include "PeripheralPins.h" + +/* ===== + * Note: Commented lines are alternative possibilities which are not used per default. + * If you change them, you will have to know what you do + * ===== + */ + +//*** ADC *** + +#ifdef HAL_ADC_MODULE_ENABLED +const PinMap PinMap_ADC[] = { + {PA_0, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC1_IN0 + {PA_1, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC1_IN1 + {PA_2, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC1_IN2 + {PA_3, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC1_IN3 + {PA_4, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC1_IN4 + {PA_5, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC1_IN5 + {PA_6, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)}, // ADC1_IN6 + {PA_7, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC1_IN7 + {PB_0, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 8, 0)}, // ADC1_IN8 + {PB_1, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 9, 0)}, // ADC1_IN9 + {NC, NP, 0} +}; +#endif + +//*** No DAC *** + +//*** I2C *** + +#ifdef HAL_I2C_MODULE_ENABLED +const PinMap PinMap_I2C_SDA[] = { + {PB_3, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF9_I2C2)}, + {PB_4, I2C3, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF9_I2C3)}, + {PB_7, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C1)}, + {PB_9, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C1)}, + {NC, NP, 0} +}; +#endif + +#ifdef HAL_I2C_MODULE_ENABLED +const PinMap PinMap_I2C_SCL[] = { + {PA_8, I2C3, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C3)}, + {PB_6, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C1)}, + {PB_8, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C1)}, + {PB_10, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C2)}, + {NC, NP, 0} +}; +#endif + +//*** PWM *** + +#ifdef HAL_TIM_MODULE_ENABLED +const PinMap PinMap_PWM[] = { + // {PA_0, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 1, 0)}, // TIM2_CH1 + {PA_0, TIM5, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM5, 1, 0)}, // TIM5_CH1 + // {PA_1, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 2, 0)}, // TIM2_CH2 + {PA_1, TIM5, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM5, 2, 0)}, // TIM5_CH2 + // {PA_2, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 3, 0)}, // TIM2_CH3 + {PA_2, TIM5, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM5, 3, 0)}, // TIM5_CH3 + // {PA_2, TIM9, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM9, 1, 0)}, // TIM9_CH1 + // {PA_3, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 4, 0)}, // TIM2_CH4 + {PA_3, TIM5, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM5, 4, 0)}, // TIM5_CH4 + // {PA_3, TIM9, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM9, 2, 0)}, // TIM9_CH2 + {PA_5, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 1, 0)}, // TIM2_CH1 + {PA_6, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 1, 0)}, // TIM3_CH1 + {PA_7, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 1)}, // TIM1_CH1N + // {PA_7, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 2, 0)}, // TIM3_CH2 + {PA_8, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 0)}, // TIM1_CH1 + {PA_9, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 2, 0)}, // TIM1_CH2 + {PA_10, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 3, 0)}, // TIM1_CH3 + // {PA_11, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 4, 0)}, // TIM1_CH4 // USB_DM + {PA_15, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 1, 0)}, // TIM2_CH1 + // {PB_0, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 2, 1)}, // TIM1_CH2N + {PB_0, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 3, 0)}, // TIM3_CH3 + // {PB_1, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 3, 1)}, // TIM1_CH3N + {PB_1, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 4, 0)}, // TIM3_CH4 + {PB_3, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 2, 0)}, // TIM2_CH2 + {PB_4, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 1, 0)}, // TIM3_CH1 + {PB_5, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 2, 0)}, // TIM3_CH2 + {PB_6, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 1, 0)}, // TIM4_CH1 + {PB_7, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 2, 0)}, // TIM4_CH2 + // {PB_8, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 3, 0)}, // TIM4_CH3 + {PB_8, TIM10, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM10, 1, 0)}, // TIM10_CH1 + // {PB_9, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 4, 0)}, // TIM4_CH4 + {PB_9, TIM11, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM11, 1, 0)}, // TIM11_CH1 + {PB_10, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 3, 0)}, // TIM2_CH3 + {PB_13, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 1)}, // TIM1_CH1N + {PB_14, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 2, 1)}, // TIM1_CH2N + {PB_15, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 3, 1)}, // TIM1_CH3N + {NC, NP, 0} +}; +#endif + +//*** SERIAL *** + +#ifdef HAL_UART_MODULE_ENABLED +const PinMap PinMap_UART_TX[] = { + {PA_2, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)}, + {PA_9, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)}, + // {PA_11, USART6, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_USART6)}, // USB_DM + {PB_6, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)}, + {NC, NP, 0} +}; +#endif + +#ifdef HAL_UART_MODULE_ENABLED +const PinMap PinMap_UART_RX[] = { + {PA_3, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)}, + {PA_10, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)}, + // {PA_12, USART6, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_USART6)}, // USB_DP + {PB_7, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)}, + {NC, NP, 0} +}; +#endif + +#ifdef HAL_UART_MODULE_ENABLED +const PinMap PinMap_UART_RTS[] = { + {PA_1, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)}, + // {PA_12, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)}, // USB_DM + {NC, NP, 0} +}; +#endif + +#ifdef HAL_UART_MODULE_ENABLED +const PinMap PinMap_UART_CTS[] = { + {PA_0, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)}, + // {PA_11, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)}, // USB_DP + {NC, NP, 0} +}; +#endif + +//*** SPI *** + +#ifdef HAL_SPI_MODULE_ENABLED +const PinMap PinMap_SPI_MOSI[] = { + {PA_7, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)}, + // {PB_5, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)}, + {PB_5, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)}, + {PB_15, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)}, + {NC, NP, 0} +}; +#endif + +#ifdef HAL_SPI_MODULE_ENABLED +const PinMap PinMap_SPI_MISO[] = { + {PA_6, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)}, + // {PB_4, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)}, + {PB_4, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)}, + {PB_14, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)}, + {NC, NP, 0} +}; +#endif + +#ifdef HAL_SPI_MODULE_ENABLED +const PinMap PinMap_SPI_SCLK[] = { + {PA_5, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)}, + // {PB_3, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)}, + {PB_3, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)}, + {PB_10, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)}, + {PB_13, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)}, + {NC, NP, 0} +}; +#endif + +#ifdef HAL_SPI_MODULE_ENABLED +const PinMap PinMap_SPI_SSEL[] = { + {PA_4, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)}, + // {PA_4, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)}, + // {PA_15, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)}, + {PA_15, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)}, + {PB_9, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)}, + {PB_12, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)}, + {NC, NP, 0} +}; +#endif + +//*** No CAN *** + +//*** No ETHERNET *** + +//*** No QUADSPI *** + +//*** USB *** + +#ifdef HAL_PCD_MODULE_ENABLED +const PinMap PinMap_USB_OTG_FS[] = { + // {PA_8, USB_OTG_FS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_OTG_FS)}, // USB_OTG_FS_SOF + // {PA_9, USB_OTG_FS, STM_PIN_DATA(STM_MODE_INPUT, GPIO_NOPULL, GPIO_AF_NONE)}, // USB_OTG_FS_VBUS + // {PA_10, USB_OTG_FS, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_PULLUP, GPIO_AF10_OTG_FS)}, // USB_OTG_FS_ID + {PA_11, USB_OTG_FS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_OTG_FS)}, // USB_OTG_FS_DM + {PA_12, USB_OTG_FS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_OTG_FS)}, // USB_OTG_FS_DP + {NC, NP, 0} +}; +#endif + +//*** No USB_OTG_HS *** diff --git a/variants/PILL_F411XX/PinNamesVar.h b/variants/PILL_F411XX/PinNamesVar.h new file mode 100644 index 0000000000..e90a617cc5 --- /dev/null +++ b/variants/PILL_F411XX/PinNamesVar.h @@ -0,0 +1,33 @@ +/* SYS_WKUP */ +#ifdef PWR_WAKEUP_PIN1 +SYS_WKUP1 = PA_0, +#endif +#ifdef PWR_WAKEUP_PIN2 +SYS_WKUP2 = NC, +#endif +#ifdef PWR_WAKEUP_PIN3 +SYS_WKUP3 = NC, +#endif +#ifdef PWR_WAKEUP_PIN4 +SYS_WKUP4 = NC, +#endif +#ifdef PWR_WAKEUP_PIN5 +SYS_WKUP5 = NC, +#endif +#ifdef PWR_WAKEUP_PIN6 +SYS_WKUP6 = NC, +#endif +#ifdef PWR_WAKEUP_PIN7 +SYS_WKUP7 = NC, +#endif +#ifdef PWR_WAKEUP_PIN8 +SYS_WKUP8 = NC, +#endif +/* USB */ +#ifdef USBCON +USB_OTG_FS_SOF = PA_8, +USB_OTG_FS_VBUS = PA_9, +USB_OTG_FS_ID = PA_10, +USB_OTG_FS_DM = PA_11, +USB_OTG_FS_DP = PA_12, +#endif \ No newline at end of file diff --git a/variants/PILL_F411XX/ldscript.ld b/variants/PILL_F411XX/ldscript.ld new file mode 100644 index 0000000000..2781f63ecf --- /dev/null +++ b/variants/PILL_F411XX/ldscript.ld @@ -0,0 +1,188 @@ +/* +***************************************************************************** +** + +** File : LinkerScript.ld +** +** Abstract : Linker script for STM32F401CCUx Device with +** 256KByte FLASH, 64KByte RAM +** +** Set heap size, stack size and stack location according +** to application requirements. +** +** Set memory bank area and size if external memory is used. +** +** Target : STMicroelectronics STM32 +** +** +** Distribution: The file is distributed as is, without any warranty +** of any kind. +** +***************************************************************************** +** @attention +** +**

© COPYRIGHT(c) 2014 Ac6

+** +** Redistribution and use in source and binary forms, with or without modification, +** are permitted provided that the following conditions are met: +** 1. Redistributions of source code must retain the above copyright notice, +** this list of conditions and the following disclaimer. +** 2. Redistributions in binary form must reproduce the above copyright notice, +** this list of conditions and the following disclaimer in the documentation +** and/or other materials provided with the distribution. +** 3. Neither the name of Ac6 nor the names of its contributors +** may be used to endorse or promote products derived from this software +** without specific prior written permission. +** +** THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +** AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE +** IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE +** DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE +** FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL +** DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR +** SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER +** CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, +** OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE +** OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. +** +***************************************************************************** +*/ + +/* Entry Point */ +ENTRY(Reset_Handler) + +/* Highest address of the user mode stack */ +_estack = 0x20020000; /* end of RAM */ +/* Generate a link error if heap and stack don't fit into RAM */ +_Min_Heap_Size = 0x200; /* required amount of heap */ +_Min_Stack_Size = 0x400; /* required amount of stack */ + +/* Specify the memory areas */ +MEMORY +{ +RAM (xrw) : ORIGIN = 0x20000000, LENGTH = 128K +FLASH (rx) : ORIGIN = 0x8000000, LENGTH = 512K +} + +/* Define output sections */ +SECTIONS +{ + /* The startup code goes first into FLASH */ + .isr_vector : + { + . = ALIGN(4); + KEEP(*(.isr_vector)) /* Startup code */ + . = ALIGN(4); + } >FLASH + + /* The program code and other data goes into FLASH */ + .text : + { + . = ALIGN(4); + *(.text) /* .text sections (code) */ + *(.text*) /* .text* sections (code) */ + *(.glue_7) /* glue arm to thumb code */ + *(.glue_7t) /* glue thumb to arm code */ + *(.eh_frame) + + KEEP (*(.init)) + KEEP (*(.fini)) + + . = ALIGN(4); + _etext = .; /* define a global symbols at end of code */ + } >FLASH + + /* Constant data goes into FLASH */ + .rodata : + { + . = ALIGN(4); + *(.rodata) /* .rodata sections (constants, strings, etc.) */ + *(.rodata*) /* .rodata* sections (constants, strings, etc.) */ + . = ALIGN(4); + } >FLASH + + .ARM.extab : { *(.ARM.extab* .gnu.linkonce.armextab.*) } >FLASH + .ARM : { + __exidx_start = .; + *(.ARM.exidx*) + __exidx_end = .; + } >FLASH + + .preinit_array : + { + PROVIDE_HIDDEN (__preinit_array_start = .); + KEEP (*(.preinit_array*)) + PROVIDE_HIDDEN (__preinit_array_end = .); + } >FLASH + .init_array : + { + PROVIDE_HIDDEN (__init_array_start = .); + KEEP (*(SORT(.init_array.*))) + KEEP (*(.init_array*)) + PROVIDE_HIDDEN (__init_array_end = .); + } >FLASH + .fini_array : + { + PROVIDE_HIDDEN (__fini_array_start = .); + KEEP (*(SORT(.fini_array.*))) + KEEP (*(.fini_array*)) + PROVIDE_HIDDEN (__fini_array_end = .); + } >FLASH + + /* used by the startup to initialize data */ + _sidata = LOADADDR(.data); + + /* Initialized data sections goes into RAM, load LMA copy after code */ + .data : + { + . = ALIGN(4); + _sdata = .; /* create a global symbol at data start */ + *(.data) /* .data sections */ + *(.data*) /* .data* sections */ + + . = ALIGN(4); + _edata = .; /* define a global symbol at data end */ + } >RAM AT> FLASH + + + /* Uninitialized data section */ + . = ALIGN(4); + .bss : + { + /* This is used by the startup in order to initialize the .bss secion */ + _sbss = .; /* define a global symbol at bss start */ + __bss_start__ = _sbss; + *(.bss) + *(.bss*) + *(COMMON) + + . = ALIGN(4); + _ebss = .; /* define a global symbol at bss end */ + __bss_end__ = _ebss; + } >RAM + + /* User_heap_stack section, used to check that there is enough RAM left */ + ._user_heap_stack : + { + . = ALIGN(8); + PROVIDE ( end = . ); + PROVIDE ( _end = . ); + . = . + _Min_Heap_Size; + . = . + _Min_Stack_Size; + . = ALIGN(8); + } >RAM + + + + /* Remove information from the standard libraries */ + /DISCARD/ : + { + libc.a ( * ) + libm.a ( * ) + libgcc.a ( * ) + } + + .ARM.attributes 0 : { *(.ARM.attributes) } +} + + diff --git a/variants/PILL_F411XX/variant.cpp b/variants/PILL_F411XX/variant.cpp new file mode 100644 index 0000000000..2e4d196c18 --- /dev/null +++ b/variants/PILL_F411XX/variant.cpp @@ -0,0 +1,141 @@ +/* + ******************************************************************************* + * Copyright (c) 2018, STMicroelectronics + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions are met: + * + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + ******************************************************************************* + */ +#include "pins_arduino.h" + +#ifdef __cplusplus +extern "C" { +#endif + +// Pin number +const PinName digitalPin[] = { + /* USB connector on the top, MCU side */ + /* Left Side */ + PB_9, //D0 + PB_8, //D1 + PB_7, //D2 + PB_6, //D3 + PB_5, //D4 + PB_4, //D5 + PB_3, //D6 + PA_15, //D7 + PA_12, //D8 - USB DP + PA_11, //D9 - USB DM + PA_10, //D10 + PA_9, //D11 + PA_8, //D12 + PB_15, //D13 + PB_14, //D14 + PB_13, //D15 + PB_12, //D16 + /* Right side */ + PC_13, //D17 - LED + PC_14, //D18 + PC_15, //D19 + PA_0, //D20/A0 + PA_1, //D21/A1 + PA_2, //D22/A2 + PA_3, //D23/A3 + PA_4, //D24/A4 + PA_5, //D25/A5 + PA_6, //D26/A6 + PA_7, //D27/A7 + PB_0, //D28/A8 + PB_1, //D29/A9 + PB_10, //D30 + PB_2, //D31 - BOOT1 + PA_13, //D32 - SWDI0 + PA_14, //D33 - SWCLK +}; + +#ifdef __cplusplus +} +#endif + +// ---------------------------------------------------------------------------- + +#ifdef __cplusplus +extern "C" { +#endif +/** + * @brief System Clock Configuration + * The system Clock is configured as follow : + * System Clock source = PLL (HSI) + * SYSCLK(Hz) = 96000000 + * HCLK(Hz) = 96000000 + * AHB Prescaler = 1 + * APB1 Prescaler = 2 + * APB2 Prescaler = 1 + * HSI Frequency(Hz) = 16000000 + * PLL_M = 25 + * PLL_N = 192 + * PLL_P = 2 + * PLL_Q = 4 + * VDD(V) = 3.3 + * Main regulator output voltage = Scale2 mode + * Flash Latency(WS) = 2 + * @param None + * @retval None + */ +WEAK void SystemClock_Config(void) +{ + RCC_OscInitTypeDef RCC_OscInitStruct = {}; + RCC_ClkInitTypeDef RCC_ClkInitStruct = {}; + + /* Configure the main internal regulator output voltage */ + __HAL_RCC_PWR_CLK_ENABLE(); + __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE2); + /* Initializes the CPU, AHB and APB busses clocks */ + RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE; + RCC_OscInitStruct.HSEState = RCC_HSE_ON; + RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON; + RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE; + RCC_OscInitStruct.PLL.PLLM = 25; + RCC_OscInitStruct.PLL.PLLN = 192; + RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; + RCC_OscInitStruct.PLL.PLLQ = 4; + if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) { + Error_Handler(); + } + /* Initializes the CPU, AHB and APB busses clocks */ + RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_SYSCLK + | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2; + RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; + RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; + RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2; + RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1; + + if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_3) != HAL_OK) { + Error_Handler(); + } +} + +#ifdef __cplusplus +} +#endif diff --git a/variants/PILL_F411XX/variant.h b/variants/PILL_F411XX/variant.h new file mode 100644 index 0000000000..47f5de07c9 --- /dev/null +++ b/variants/PILL_F411XX/variant.h @@ -0,0 +1,142 @@ +/* + ******************************************************************************* + * Copyright (c) 2018, STMicroelectronics + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions are met: + * + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + ******************************************************************************* + */ +#ifndef _VARIANT_ARDUINO_STM32_ +#define _VARIANT_ARDUINO_STM32_ + +#ifdef __cplusplus +extern "C" { +#endif // __cplusplus + +/*---------------------------------------------------------------------------- + * Pins + *----------------------------------------------------------------------------*/ + +// USB connector on bottom, MCU Side +// Left Side +#define PB9 0 +#define PB8 1 +#define PB7 2 +#define PB6 3 +#define PB5 4 +#define PB4 5 +#define PB3 6 +#define PA15 7 +#define PA12 8 // USB DP +#define PA11 9 // USB DM +#define PA10 10 +#define PA9 11 +#define PA8 12 +#define PB15 13 +#define PB14 14 +#define PB13 15 +#define PB12 16 +// Right side +#define PC13 17 // LED +#define PC14 18 +#define PC15 19 +#define PA0 20 // A0 +#define PA1 21 // A1 +#define PA2 22 // A2 +#define PA3 23 // A3 +#define PA4 24 // A4 +#define PA5 25 // A5 +#define PA6 26 // A6 +#define PA7 27 // A7 +#define PB0 28 // A8 +#define PB1 29 // A9 +#define PB10 30 + +// Other +#define PB2 31 // BOOT1 +#define PA13 32 // SWDI0 +#define PA14 33 // SWCLK + +// This must be a literal +#define NUM_DIGITAL_PINS 34 +// This must be a literal with a value less than or equal to to MAX_ANALOG_INPUTS +#define NUM_ANALOG_INPUTS 10 +#define NUM_ANALOG_FIRST 20 + +// On-board LED pin number +#define LED_BUILTIN PC13 + + +// SPI Definitions +#define PIN_SPI_SS PA4 +#define PIN_SPI_MOSI PA7 +#define PIN_SPI_MISO PA6 +#define PIN_SPI_SCK PA5 + +// I2C Definitions +#define PIN_WIRE_SDA PB7 +#define PIN_WIRE_SCL PB6 + +// Timer Definitions +#define TIMER_TONE TIM10 +#define TIMER_SERVO TIM11 + +// UART Definitions +#define SERIAL_UART_INSTANCE 1 +// Default pin used for 'Serial' instance +// Mandatory for Firmata +#define PIN_SERIAL_RX PA10 +#define PIN_SERIAL_TX PA9 + +/* HAL configuration */ +#define HSE_VALUE 25000000U + +#ifdef __cplusplus +} // extern "C" +#endif +/*---------------------------------------------------------------------------- + * Arduino objects - C++ only + *----------------------------------------------------------------------------*/ + +#ifdef __cplusplus +// These serial port names are intended to allow libraries and architecture-neutral +// sketches to automatically default to the correct port name for a particular type +// of use. For example, a GPS module would normally connect to SERIAL_PORT_HARDWARE_OPEN, +// the first hardware serial port whose RX/TX pins are not dedicated to another use. +// +// SERIAL_PORT_MONITOR Port which normally prints to the Arduino Serial Monitor +// +// SERIAL_PORT_USBVIRTUAL Port which is USB virtual serial +// +// SERIAL_PORT_LINUXBRIDGE Port which connects to a Linux system via Bridge library +// +// SERIAL_PORT_HARDWARE Hardware serial port, physical RX & TX pins. +// +// SERIAL_PORT_HARDWARE_OPEN Hardware serial ports which are open for use. Their RX & TX +// pins are NOT connected to anything by default. +#define SERIAL_PORT_MONITOR Serial +#define SERIAL_PORT_HARDWARE Serial1 +#endif + +#endif /* _VARIANT_ARDUINO_STM32_ */