Mechanical Assembly draft

Author: marqdevx

content/hardware/04.pro/miscellaneous/wisgate-edge-pro/tutorials/pole-mounting/content.md

@@ -0,0 +1,95 @@
+---
+title: 'Mounting WisGate Edge PRO Gateway on a Pole'
+description: 'Tutorial for mounting the WisGate Edge Lo-Ra Gateway in an antenna Pole'
+difficulty: easy
+tags: 
+  - Mechanical
+  - Setup
+author: 'Pablo Marquínez'
+hardware:
+  - hardware/05.pro/mmiscellaneousis/WisGate-edge-pro
+---
+
+## Introduction 
+
+This tutorial will show you how to mount your **WisGate Edge** gateway on an outdoors pole.
+
+## Goals
+
+The goals of this article are:
+
+- Assembly the mechanical pieces on the device
+- Attach the device on your pole
+
+## Hardware & Software Needed
+
+- [WisGate Edge Pro](https://store.arduino.cc/products/wisgate-edge-pro)
+
+## Instructions
+
+The mechanical pieces are included with the device, those will make the device fit on an outdoors pole firmly and safe.
+* 2 Clamps
+* 1 Bracket
+* 2 Antennas
+
+### Assembly the Bracket to the Enclosure
+
+Turn the gateway, on the back it has four holes for screws, align those with the bracket and screw them.
+
+The bar from the bracket should be on the aiming towards the top, where the antennas are connected.
+
+
+<iframe 
+  width="720" 
+  height="405" 
+  loop="true" 
+  src="https://www.youtube.com/embed/xvFH9clAQwg?autoplay=1&controls=0&loop=1&mute=1&playlist=xvFH9clAQwg" frameborder="0"
+  >
+</iframe>
+
+### Clamps on the Pole
+
+Take the bigger clamp and introduce one screw on the hole that fits better for your pole, grab the smaller clamp and align it with the screw, after that you should take a nut and make it closer to the smaller clamp, repeat it with the other side, first just make sure everything is aligned and then fasten them properly with a screwdriver.
+
+***The clamp is also suitable to be mounted using hose clamps (not included) you should then use the rectangular holes on the bigger clamp***
+
+<iframe 
+  width="720" 
+  height="405" 
+  loop="true" 
+  src="https://www.youtube.com/embed/tVmZoD38XZo?autoplay=1&controls=0&loop=1&mute=1&playlist=tVmZoD38XZo" frameborder="0"
+  >
+</iframe>
+
+### Attaching the bracket on the clamps
+
+Once both the bracket on the gateway and the clamps on the pole are properly fasten, it is time to attach the gateway to the pole.
+After it's attached fasten one M6*12 screws on each side.
+
+As shown in the following video:
+
+<iframe 
+  width="720" 
+  height="405" 
+  loop="true" 
+  src="https://www.youtube.com/embed/PZONsccUlMo?autoplay=1&controls=0&loop=1&mute=1&playlist=PZONsccUlMo" frameborder="0"
+  >
+</iframe>
+
+### Coupling the Antennas
+
+On the top side of the gateway fasten both N-Type fiberglass antennas.
+
+<iframe 
+  width="720" 
+  height="405" 
+  loop="true" 
+  src="https://www.youtube.com/embed/6KmyJA9n28I?autoplay=1&controls=0&loop=1&mute=1&playlist=6KmyJA9n28I" frameborder="0"
+  >
+</iframe>
+
+
+## Next Step
+
+
+## Conclusion