Merge branch 'main' into soft_se

Author: pennam

.github/workflows/compile-examples.yml

@@ -96,6 +96,7 @@ jobs:
               - libraries/OTAUpdate
               - libraries/OPAMP
               - libraries/SoftwareATSE
+              - libraries/Preferences
           - board:
               fqbn: "arduino-git:renesas:minima"
             additional-sketch-paths: |

bootloaders/UNO_R4/README.md

@@ -45,7 +45,7 @@ stty -F $portname 2400
 
 Then flash the bootloader with [`rfp-cli`](https://www.renesas.com/us/en/software-tool/renesas-flash-programmer-programming-gui#download)
 ```
-rfp-cli -device ra -port $portname -p dfu_wifi.hex
+rfp-cli -device ra -dtr -port $portname -p dfu_wifi.hex
 ```
 
 :rocket: `How to load bootloader (UNO R4 Minima)`

extras/uno-r4-wifi-usb-bridge

@@ -0,0 +1,56 @@
+/*
+This example shows how to use Preferences (nvs) to store a
+structure.  Note that the maximum size of a putBytes is 496K
+or 97% of the nvs partition size.  nvs has signifcant overhead,
+so should not be used for data that will change often.
+*/
+#include <Preferences.h>
+Preferences prefs;
+
+typedef struct {
+  uint8_t hour;
+  uint8_t minute;
+  uint8_t setting1;
+  uint8_t setting2;
+} schedule_t;
+
+void setup() {
+  Serial.begin(115200);
+
+  if (!prefs.begin("schedule")) { // use "schedule" namespace
+    Serial.println("Cannot initialize preferences");
+    Serial.println("Make sure your WiFi firmware version is greater than 0.3.0");
+    while(1) {};
+  }
+  uint8_t content[] = {9, 30, 235, 255, 20, 15, 0, 1}; // two entries
+  prefs.putBytes("schedule", content, sizeof(content));
+  size_t schLen = prefs.getBytesLength("schedule");
+  char buffer[schLen]; // prepare a buffer for the data
+  prefs.getBytes("schedule", buffer, schLen);
+  if (schLen % sizeof(schedule_t)) { // simple check that data fits
+    Serial.println("Data is not correct size!");
+    return;
+  }
+  schedule_t *schedule = (schedule_t *) buffer; // cast the bytes into a struct ptr
+  Serial.print(schedule[1].hour);
+  Serial.print(":");
+  Serial.print(schedule[1].minute);
+  Serial.print(" ");
+  Serial.print(schedule[1].setting1);
+  Serial.print("/");
+  Serial.print(schedule[1].setting2);
+  Serial.println();
+
+  schedule[2] = {8, 30, 20, 21}; // add a third entry (unsafely)
+
+  // force the struct array into a byte array
+  prefs.putBytes("schedule", schedule, 3*sizeof(schedule_t));
+  schLen = prefs.getBytesLength("schedule");
+  char buffer2[schLen];
+  prefs.getBytes("schedule", buffer2, schLen);
+  for (int x=0; x<schLen; x++) Serial.print((uint8_t)buffer[x]);
+  Serial.println();
+  prefs.end();
+}
+
+void loop() {}

libraries/Preferences/examples/Prefs2Struct/Prefs2Struct.ino

@@ -0,0 +1,61 @@
+/*
+ Microcontroller startup counter example with ESP32 Preferences library.
+
+ This simple example demonstrates using the Preferences library to store how many times
+ the microcontroller has booted. The Preferences library is a wrapper around the Non-volatile
+ storage on ESP32 processor.
+
+ created for arduino-esp32 09 Feb 2017
+ by Martin Sloup (Arcao)
+*/
+
+#include <Preferences.h>
+
+Preferences preferences;
+
+void setup() {
+  Serial.begin(115200);
+  Serial.println();
+
+  // Open Preferences with my-app namespace. Each application module, library, etc
+  // has to use a namespace name to prevent key name collisions. We will open storage in
+  // RW-mode (second parameter has to be false).
+  // Note: Namespace name is limited to 15 chars.
+  if (!preferences.begin("my-app", false)) {
+    Serial.println("Cannot initialize preferences");
+    Serial.println("Make sure your WiFi firmware version is greater than 0.3.0");
+    while(1) {};
+  }
+
+  // Remove all preferences under the opened namespace
+  //preferences.clear();
+
+  // Or remove the counter key only
+  //preferences.remove("counter");
+
+  // Get the counter value, if the key does not exist, return a default value of 0
+  // Note: Key name is limited to 15 chars.
+  unsigned int counter = preferences.getUInt("counter", 0);
+
+  // Increase counter by 1
+  counter++;
+
+  // Print the counter to Serial Monitor
+  Serial.print("Current counter value: ");
+  Serial.println(counter);
+
+  // Store the counter to the Preferences
+  preferences.putUInt("counter", counter);
+
+  // Close the Preferences
+  preferences.end();
+
+  // Wait 10 seconds
+  Serial.println("Restarting in 10 seconds...");
+  delay(10000);
+
+  // Reset
+  NVIC_SystemReset();
+}
+
+void loop() {}

libraries/Preferences/examples/StartCounter/StartCounter.ino

@@ -0,0 +1,54 @@
+#######################################
+# Syntax Coloring Map NVS
+#######################################
+
+#######################################
+# Datatypes (KEYWORD1)
+#######################################
+
+Preferences	KEYWORD1
+
+#######################################
+# Methods and Functions (KEYWORD2)
+#######################################
+begin	KEYWORD2
+end	KEYWORD2
+
+clear	KEYWORD2
+remove	KEYWORD2
+
+putChar	KEYWORD2
+putUChar	KEYWORD2
+putShort	KEYWORD2
+putUShort	KEYWORD2
+putInt	KEYWORD2
+putUInt	KEYWORD2
+putLong	KEYWORD2
+putULong	KEYWORD2
+putLong64	KEYWORD2
+putULong64	KEYWORD2
+putFloat	KEYWORD2
+putDouble	KEYWORD2
+putBool	KEYWORD2
+putString	KEYWORD2
+putBytes	KEYWORD2
+
+getChar	KEYWORD2
+getUChar	KEYWORD2
+getShort	KEYWORD2
+getUShort	KEYWORD2
+getInt	KEYWORD2
+getUInt	KEYWORD2
+getLong	KEYWORD2
+getULong	KEYWORD2
+getLong64	KEYWORD2
+getULong64	KEYWORD2
+getFloat	KEYWORD2
+getDouble	KEYWORD2
+getBool	KEYWORD2
+getString	KEYWORD2
+getBytes	KEYWORD2
+
+#######################################
+# Constants (LITERAL1)
+#######################################

libraries/Preferences/keywords.txt

@@ -0,0 +1,9 @@
+name=Preferences
+version=2.0.0
+author=Hristo Gochkov
+maintainer=Hristo Gochkov <hristo@espressif.com>
+sentence=Provides friendly access to ESP32's Non-Volatile Storage
+paragraph=
+category=Data Storage
+url=
+architectures=renesas,renesas_uno