diff --git a/adafruit_epd/epd.py b/adafruit_epd/epd.py
index 39afa09..ac49c1b 100644
--- a/adafruit_epd/epd.py
+++ b/adafruit_epd/epd.py
@@ -340,24 +340,19 @@ def image(self, image):
         if imwidth != self.width or imheight != self.height:
             raise ValueError('Image must be same dimensions as display ({0}x{1}).' \
                 .format(self.width, self.height))
+        if self.sram:
+            raise RuntimeError("PIL image is not for use with SRAM assist")
         # Grab all the pixels from the image, faster than getpixel.
         pix = image.load()
+        # clear out any display buffers
+        self.fill(Adafruit_EPD.WHITE)
 
-        for y in iter(range(image.size[1])):
-            for x in iter(range(image.size[0])):
-                if x == 0:
-                    x = 1
+        for y in range(image.size[1]):
+            for x in range(image.size[0]):
                 pixel = pix[x, y]
-
-                addr = int(((self._width - x) * self._height + y)/8)
-
-                if pixel == (0xFF, 0, 0):
-                    addr = addr + self._buffer1_size
-                current = self.sram.read8(addr)
-
-                if pixel in ((0xFF, 0, 0), (0, 0, 0)):
-                    current = current & ~(1 << (7 - y%8))
-                else:
-                    current = current | (1 << (7 - y%8))
-
-                self.sram.write8(addr, current)
+                if (pixel[0] >= 0x80) and (pixel[1] < 0x80) and (pixel[2] < 0x80):
+                    # reddish
+                    self.pixel(x, y, Adafruit_EPD.RED)
+                elif (pixel[0] < 0x80) and (pixel[1] < 0x80) and (pixel[2] < 0x80):
+                    # dark
+                    self.pixel(x, y, Adafruit_EPD.BLACK)
diff --git a/adafruit_epd/ssd1675.py b/adafruit_epd/ssd1675.py
index 96f15da..f2f1f7f 100644
--- a/adafruit_epd/ssd1675.py
+++ b/adafruit_epd/ssd1675.py
@@ -68,10 +68,11 @@ class Adafruit_SSD1675(Adafruit_EPD):
     def __init__(self, width, height, spi, *, cs_pin, dc_pin, sramcs_pin, rst_pin, busy_pin):
         super(Adafruit_SSD1675, self).__init__(width, height, spi, cs_pin, dc_pin,
                                                sramcs_pin, rst_pin, busy_pin)
-        if width % 8 != 0:
-            width += (8 - width % 8)
+        stride = width
+        if stride % 8 != 0:
+            stride += (8 - stride % 8)
 
-        self._buffer1_size = int(width * height / 8)
+        self._buffer1_size = int(stride * height / 8)
         self._buffer2_size = self._buffer1_size
 
         if sramcs_pin:
@@ -82,9 +83,9 @@ def __init__(self, width, height, spi, *, cs_pin, dc_pin, sramcs_pin, rst_pin, b
             self._buffer2 = bytearray(self._buffer2_size)
         # since we have *two* framebuffers - one for red and one for black
         # we dont subclass but manage manually
-        self._framebuf1 = adafruit_framebuf.FrameBuffer(self._buffer1, width, height,
+        self._framebuf1 = adafruit_framebuf.FrameBuffer(self._buffer1, width, height, stride=stride,
                                                         buf_format=adafruit_framebuf.MHMSB)
-        self._framebuf2 = adafruit_framebuf.FrameBuffer(self._buffer2, width, height,
+        self._framebuf2 = adafruit_framebuf.FrameBuffer(self._buffer2, width, height, stride=stride,
                                                         buf_format=adafruit_framebuf.MHMSB)
         self.set_black_buffer(0, True)
         self.set_color_buffer(0, True)
diff --git a/adafruit_epd/ssd1675b.py b/adafruit_epd/ssd1675b.py
new file mode 100644
index 0000000..f9e8fd9
--- /dev/null
+++ b/adafruit_epd/ssd1675b.py
@@ -0,0 +1,214 @@
+# The MIT License (MIT)
+#
+# Copyright (c) 2018 Dean Miller for Adafruit Industries
+#
+# Permission is hereby granted, free of charge, to any person obtaining a copy
+# of this software and associated documentation files (the "Software"), to deal
+# in the Software without restriction, including without limitation the rights
+# to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+# copies of the Software, and to permit persons to whom the Software is
+# furnished to do so, subject to the following conditions:
+#
+# The above copyright notice and this permission notice shall be included in
+# all copies or substantial portions of the Software.
+#
+# THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+# IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+# FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+# AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+# LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+# OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+# THE SOFTWARE.
+"""
+`adafruit_epd.ssd1675b` - Adafruit SSD1675 - ePaper display driver
+====================================================================================
+CircuitPython driver for Adafruit SSD1675 display breakouts
+* Author(s): Dean Miller, Ladyada
+"""
+
+import time
+from micropython import const
+import adafruit_framebuf
+from adafruit_epd.epd import Adafruit_EPD
+
+__version__ = "0.0.0-auto.0"
+__repo__ = "https://github.com/adafruit/Adafruit_CircuitPython_EPD.git"
+
+_SSD1675B_DRIVER_CONTROL = const(0x01)
+_SSD1675B_GATE_VOLTAGE = const(0x03)
+_SSD1675B_SOURCE_VOLTAGE = const(0x04)
+_SSD1675B_INIT_SETTING = const(0x08)
+_SSD1675B_INIT_WRITE_REG = const(0x09)
+_SSD1675B_INIT_READ_REG = const(0x0A)
+_SSD1675B_BOOSTER_SOFT_START = const(0x0C)
+_SSD1675B_GATESCAN_START = const(0x0F)
+_SSD1675B_DEEP_SLEEP = const(0x10)
+_SSD1675B_DATA_MODE = const(0x11)
+_SSD1675B_SW_RESET = const(0x12)
+_SSD1675B_HV_READY = const(0x14)
+_SSD1675B_VCI_READY = const(0x15)
+_SSD1675B_TEMP_CONTROL = const(0x18)
+_SSD1675B_TEMP_WRITE = const(0x1A)
+_SSD1675B_TEMP_READ = const(0x1B)
+_SSD1675B_EXTTEMP_WRITE = const(0x1C)
+_SSD1675B_MASTER_ACTIVATE = const(0x20)
+_SSD1675B_DISP_CTRL1 = const(0x21)
+_SSD1675B_DISP_CTRL2 = const(0x22)
+_SSD1675B_WRITE_RAM1 = const(0x24)
+_SSD1675B_WRITE_RAM2 = const(0x26)
+_SSD1675B_READ_RAM = const(0x27)
+_SSD1675B_VCOM_SENSE = const(0x28)
+_SSD1675B_VCOM_DURATION = const(0x29)
+_SSD1675B_WRITE_VCOM_OTP = const(0x2A)
+_SSD1675B_WRITE_VCOM_CTRL = const(0x2B)
+_SSD1675B_WRITE_VCOM_REG = const(0x2C)
+_SSD1675B_READ_OTP = const(0x2D)
+_SSD1675B_READ_USERID = const(0x2E)
+_SSD1675B_READ_STATUS = const(0x2F)
+_SSD1675B_WRITE_WS_OTP = const(0x30)
+_SSD1675B_LOAD_WS_OTP = const(0x31)
+_SSD1675B_WRITE_LUT = const(0x32)
+_SSD1675B_CRC_CALC = const(0x34)
+_SSD1675B_CRC_READ = const(0x35)
+_SSD1675B_PROG_OTP = const(0x36)
+_SSD1675B_WRITE_DISPLAY_OPT = const(0x37)
+_SSD1675B_WRITE_USERID = const(0x38)
+_SSD1675B_OTP_PROGMODE = const(0x39)
+_SSD1675B_WRITE_DUMMY = const(0x3A)
+_SSD1675B_WRITE_GATELINE = const(0x3B)
+_SSD1675B_WRITE_BORDER = const(0x3C)
+_SSD1675B_SET_RAMXPOS = const(0x44)
+_SSD1675B_SET_RAMYPOS = const(0x45)
+_SSD1675B_AUTOWRITE_RED = const(0x46)
+_SSD1675B_AUTOWRITE_BW = const(0x47)
+_SSD1675B_SET_RAMXCOUNT = const(0x4E)
+_SSD1675B_SET_RAMYCOUNT = const(0x4F)
+_SSD1675B_SET_ANALOGBLOCK = const(0x74)
+_SSD1675B_SET_DIGITALBLOCK = const(0x7E)
+_SSD1675B_NOP = const(0xFF)
+_LUT_DATA = b'\xa0\x90P\x00\x00\x00\x00\x00\x00\x00P\x90\xa0\x00\x00\x00\x00\x00\x00\x00\xa0\x90P\x00\x00\x00\x00\x00\x00\x00P\x90\xa0\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x0f\x0f\x00\x00\x00\x0f\x0f\x00\x00\x03\x0f\x0f\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x15A\xa82P,\x0b' # pylint: disable=line-too-long
+
+class Adafruit_SSD1675B(Adafruit_EPD):
+    """driver class for Adafruit SSD1675B ePaper display breakouts"""
+    # pylint: disable=too-many-arguments
+    def __init__(self, width, height, spi, *, cs_pin, dc_pin, sramcs_pin, rst_pin, busy_pin):
+        super(Adafruit_SSD1675B, self).__init__(width, height, spi, cs_pin, dc_pin,
+                                                sramcs_pin, rst_pin, busy_pin)
+        stride = width
+        if stride % 8 != 0:
+            stride += (8 - stride % 8)
+
+        self._buffer1_size = int(stride * height / 8)
+        self._buffer2_size = self._buffer1_size
+
+        if sramcs_pin:
+            self._buffer1 = self.sram.get_view(0)
+            self._buffer2 = self.sram.get_view(self._buffer1_size)
+        else:
+            self._buffer1 = bytearray(self._buffer1_size)
+            self._buffer2 = bytearray(self._buffer2_size)
+        # since we have *two* framebuffers - one for red and one for black
+        # we dont subclass but manage manually
+        self._framebuf1 = adafruit_framebuf.FrameBuffer(self._buffer1, width, height, stride=stride,
+                                                        buf_format=adafruit_framebuf.MHMSB)
+        self._framebuf2 = adafruit_framebuf.FrameBuffer(self._buffer2, width, height, stride=stride,
+                                                        buf_format=adafruit_framebuf.MHMSB)
+        self.set_black_buffer(0, True)
+        self.set_color_buffer(0, True)
+        # pylint: enable=too-many-arguments
+
+    def begin(self, reset=True):
+        """Begin communication with the display and set basic settings"""
+        if reset:
+            self.hardware_reset()
+        self.power_down()
+
+    def busy_wait(self):
+        """Wait for display to be done with current task, either by polling the
+        busy pin, or pausing"""
+        if self._busy:
+            while self._busy.value:
+                time.sleep(0.01)
+        else:
+            time.sleep(0.5)
+
+    def power_up(self):
+        """Power up the display in preparation for writing RAM and updating"""
+        self.hardware_reset()
+        time.sleep(0.1)
+        self.busy_wait()
+
+        self.command(_SSD1675B_SW_RESET)
+        self.busy_wait()
+
+        # set analog block control
+        self.command(_SSD1675B_SET_ANALOGBLOCK, bytearray([0x54]))
+        # set digital block control
+        self.command(_SSD1675B_SET_DIGITALBLOCK, bytearray([0x3B]))
+
+        self.command(_SSD1675B_DRIVER_CONTROL,
+                     bytearray([self._height-1, (self._height-1) >> 8, 0x00]))
+
+        # Data entry sequence
+        self.command(_SSD1675B_DATA_MODE, bytearray([0x03]))
+
+        # Set ram X start/end postion
+        self.command(_SSD1675B_SET_RAMXPOS, bytearray([0x00, self._width // 8]))
+        # Set ram Y start/end postion
+        self.command(_SSD1675B_SET_RAMYPOS,
+                     bytearray([0x0, 0x0, self._height-1, (self._height-1) >> 8]))
+
+        # Border color
+        self.command(_SSD1675B_WRITE_BORDER, bytearray([0x03]))
+
+        # Vcom Voltage
+        self.command(_SSD1675B_WRITE_VCOM_REG, bytearray([0x50]))
+        # Set gate voltage
+        self.command(_SSD1675B_GATE_VOLTAGE, _LUT_DATA[100:101])
+        # Set source voltage
+        self.command(_SSD1675B_SOURCE_VOLTAGE, _LUT_DATA[101:104])
+        # Set dummy line period
+        self.command(_SSD1675B_WRITE_DUMMY, _LUT_DATA[105:106])
+        # Set gate line width
+        self.command(_SSD1675B_WRITE_GATELINE, _LUT_DATA[106:107])
+        # LUT
+        self.command(_SSD1675B_WRITE_LUT, _LUT_DATA[0:100])
+
+        # Set temperature control
+        #self.command(_SSD1675B_TEMP_CONTROL, bytearray([0x80]))
+
+        # Set RAM X address counter
+        self.command(_SSD1675B_SET_RAMXCOUNT, bytearray([0]))
+        # Set RAM Y address counter
+        self.command(_SSD1675B_SET_RAMYCOUNT, bytearray([self._height-1, (self._height-1) >> 8]))
+
+        self.busy_wait()
+
+    def power_down(self):
+        """Power down the display - required when not actively displaying!"""
+        self.command(_SSD1675B_DEEP_SLEEP, bytearray([0x01]))
+        time.sleep(0.1)
+
+    def update(self):
+        """Update the display from internal memory"""
+        self.command(_SSD1675B_DISP_CTRL2, bytearray([0xC7]))
+        self.command(_SSD1675B_MASTER_ACTIVATE)
+        self.busy_wait()
+        if not self._busy:
+            time.sleep(3)   # wait 3 seconds
+
+    def write_ram(self, index):
+        """Send the one byte command for starting the RAM write process. Returns
+        the byte read at the same time over SPI. index is the RAM buffer, can be
+        0 or 1 for tri-color displays."""
+        if index == 0:
+            return self.command(_SSD1675B_WRITE_RAM1, end=False)
+        if index == 1:
+            return self.command(_SSD1675B_WRITE_RAM2, end=False)
+        raise RuntimeError("RAM index must be 0 or 1")
+
+    def set_ram_address(self, x, y): # pylint: disable=unused-argument, no-self-use
+        """Set the RAM address location, not used on this chipset but required by
+        the superclass"""
+        self.command(_SSD1675B_SET_RAMXCOUNT, bytearray([x]))
+        self.command(_SSD1675B_SET_RAMYCOUNT, bytearray([y, y>>8]))
diff --git a/adafruit_epd/ssd1681.py b/adafruit_epd/ssd1681.py
new file mode 100644
index 0000000..6d9ba95
--- /dev/null
+++ b/adafruit_epd/ssd1681.py
@@ -0,0 +1,176 @@
+# The MIT License (MIT)
+#
+# Copyright (c) 2018 Dean Miller for Adafruit Industries
+#
+# Permission is hereby granted, free of charge, to any person obtaining a copy
+# of this software and associated documentation files (the "Software"), to deal
+# in the Software without restriction, including without limitation the rights
+# to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+# copies of the Software, and to permit persons to whom the Software is
+# furnished to do so, subject to the following conditions:
+#
+# The above copyright notice and this permission notice shall be included in
+# all copies or substantial portions of the Software.
+#
+# THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+# IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+# FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+# AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+# LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+# OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+# THE SOFTWARE.
+"""
+`adafruit_epd.ssd1681` - Adafruit SSD1681 - ePaper display driver
+====================================================================================
+CircuitPython driver for Adafruit SSD1681 display breakouts
+* Author(s): Dean Miller, Ladyada
+"""
+
+import time
+from micropython import const
+import adafruit_framebuf
+from adafruit_epd.epd import Adafruit_EPD
+
+__version__ = "0.0.0-auto.0"
+__repo__ = "https://github.com/adafruit/Adafruit_CircuitPython_EPD.git"
+
+_SSD1681_DRIVER_CONTROL = const(0x01)
+_SSD1681_GATE_VOLTAGE = const(0x03)
+_SSD1681_SOURCE_VOLTAGE = const(0x04)
+_SSD1681_INIT_SETTING = const(0x08)
+_SSD1681_INIT_WRITE_REG = const(0x09)
+_SSD1681_INIT_READ_REG = const(0x0A)
+_SSD1681_BOOSTER_SOFT_START = const(0x0C)
+_SSD1681_DEEP_SLEEP = const(0x10)
+_SSD1681_DATA_MODE = const(0x11)
+_SSD1681_SW_RESET = const(0x12)
+_SSD1681_HV_DETECT = const(0x14)
+_SSD1681_VCI_DETECT = const(0x15)
+_SSD1681_TEMP_CONTROL = const(0x18)
+_SSD1681_TEMP_WRITE = const(0x1A)
+_SSD1681_TEMP_READ = const(0x1B)
+_SSD1681_EXTTEMP_WRITE = const(0x1C)
+_SSD1681_MASTER_ACTIVATE = const(0x20)
+_SSD1681_DISP_CTRL1 = const(0x21)
+_SSD1681_DISP_CTRL2 = const(0x22)
+_SSD1681_WRITE_BWRAM = const(0x24)
+_SSD1681_WRITE_REDRAM = const(0x26)
+_SSD1681_READ_RAM = const(0x27)
+_SSD1681_VCOM_SENSE = const(0x28)
+_SSD1681_VCOM_DURATION = const(0x29)
+_SSD1681_WRITE_VCOM_OTP = const(0x2A)
+_SSD1681_WRITE_VCOM_CTRL = const(0x2B)
+_SSD1681_WRITE_VCOM_REG = const(0x2C)
+_SSD1681_READ_OTP = const(0x2D)
+_SSD1681_READ_USERID = const(0x2E)
+_SSD1681_READ_STATUS = const(0x2F)
+_SSD1681_WRITE_WS_OTP = const(0x30)
+_SSD1681_LOAD_WS_OTP = const(0x31)
+_SSD1681_WRITE_LUT = const(0x32)
+_SSD1681_CRC_CALC = const(0x34)
+_SSD1681_CRC_READ = const(0x35)
+_SSD1681_PROG_OTP = const(0x36)
+_SSD1681_WRITE_DISPLAY_OPT = const(0x37)
+_SSD1681_WRITE_USERID = const(0x38)
+_SSD1681_OTP_PROGMODE = const(0x39)
+_SSD1681_WRITE_BORDER = const(0x3C)
+_SSD1681_END_OPTION = const(0x3F)
+_SSD1681_SET_RAMXPOS = const(0x44)
+_SSD1681_SET_RAMYPOS = const(0x45)
+_SSD1681_AUTOWRITE_RED = const(0x46)
+_SSD1681_AUTOWRITE_BW = const(0x47)
+_SSD1681_SET_RAMXCOUNT = const(0x4E)
+_SSD1681_SET_RAMYCOUNT = const(0x4F)
+_SSD1681_NOP = const(0xFF)
+
+_LUT_DATA = b'\x02\x02\x01\x11\x12\x12""fiiYX\x99\x99\x88\x00\x00\x00\x00\xf8\xb4\x13Q5QQ\x19\x01\x00' # pylint: disable=line-too-long
+
+class Adafruit_SSD1681(Adafruit_EPD):
+    """driver class for Adafruit SSD1681 ePaper display breakouts"""
+    # pylint: disable=too-many-arguments
+    def __init__(self, width, height, spi, *, cs_pin, dc_pin, sramcs_pin, rst_pin, busy_pin):
+        super(Adafruit_SSD1681, self).__init__(width, height, spi, cs_pin, dc_pin,
+                                               sramcs_pin, rst_pin, busy_pin)
+
+        if height % 8 != 0:
+            height += (8 - height % 8)
+            self._height = height
+
+        self._buffer1_size = int(width * height / 8)
+
+        if sramcs_pin:
+            self._buffer1 = self.sram.get_view(0)
+        else:
+            self._buffer1 = bytearray((width * height) // 8)
+        self._framebuf1 = adafruit_framebuf.FrameBuffer(self._buffer1, width, height,
+                                                        buf_format=adafruit_framebuf.MHMSB)
+        self.set_black_buffer(0, True)
+        self.set_color_buffer(0, True)
+        # pylint: enable=too-many-arguments
+
+    def begin(self, reset=True):
+        """Begin communication with the display and set basic settings"""
+        if reset:
+            self.hardware_reset()
+        self.power_down()
+
+    def busy_wait(self):
+        """Wait for display to be done with current task, either by polling the
+        busy pin, or pausing"""
+        if self._busy:
+            while self._busy.value:
+                time.sleep(0.01)
+        else:
+            time.sleep(0.5)
+
+    def power_up(self):
+        """Power up the display in preparation for writing RAM and updating"""
+        self.hardware_reset()
+        self.busy_wait()
+        self.command(_SSD1681_SW_RESET)
+        self.busy_wait()
+        # driver output control
+        self.command(_SSD1681_DRIVER_CONTROL,
+                     bytearray([self._width-1, (self._width-1) >> 8, 0x00]))
+        # data entry mode
+        self.command(_SSD1681_DATA_MODE, bytearray([0x03]))
+        # Set ram X start/end postion
+        self.command(_SSD1681_SET_RAMXPOS, bytearray([0x00, self._height//8 - 1]))
+        # Set ram Y start/end postion
+        self.command(_SSD1681_SET_RAMYPOS,
+                     bytearray([0, 0, self._height - 1, (self._height - 1) >> 8]))
+        # Set border waveform
+        self.command(_SSD1681_WRITE_BORDER, bytearray([0x05]))
+        # Set temperature control
+        self.command(_SSD1681_TEMP_CONTROL, bytearray([0x80]))
+
+        self.busy_wait()
+
+    def power_down(self):
+        """Power down the display - required when not actively displaying!"""
+        self.command(_SSD1681_DEEP_SLEEP, bytearray([0x01]))
+        time.sleep(0.1)
+
+    def update(self):
+        """Update the display from internal memory"""
+        self.command(_SSD1681_DISP_CTRL2, bytearray([0xF7]))
+        self.command(_SSD1681_MASTER_ACTIVATE)
+        self.busy_wait()
+        if not self._busy:
+            time.sleep(3)   # wait 3 seconds
+
+    def write_ram(self, index):
+        """Send the one byte command for starting the RAM write process. Returns
+        the byte read at the same time over SPI. index is the RAM buffer, can be
+        0 or 1 for tri-color displays."""
+        if index == 0:
+            return self.command(_SSD1681_WRITE_BWRAM, end=False)
+        raise RuntimeError("RAM index must be 0")
+
+    def set_ram_address(self, x, y): # pylint: disable=unused-argument, no-self-use
+        """Set the RAM address location, not used on this chipset but required by
+        the superclass"""
+        # Set RAM X address counter
+        self.command(_SSD1681_SET_RAMXCOUNT, bytearray([x]))
+        # Set RAM Y address counter
+        self.command(_SSD1681_SET_RAMYCOUNT, bytearray([y>>8, y]))
diff --git a/examples/epd_bitmap.py b/examples/epd_bitmap.py
index c1b1536..9591469 100644
--- a/examples/epd_bitmap.py
+++ b/examples/epd_bitmap.py
@@ -6,6 +6,8 @@
 from adafruit_epd.il91874 import Adafruit_IL91874    # pylint: disable=unused-import
 from adafruit_epd.il0398 import Adafruit_IL0398      # pylint: disable=unused-import
 from adafruit_epd.ssd1608 import Adafruit_SSD1608    # pylint: disable=unused-import
+from adafruit_epd.ssd1675 import Adafruit_SSD1675  # pylint: disable=unused-import
+
 
 # create the spi device and pins we will need
 spi = busio.SPI(board.SCK, MOSI=board.MOSI, MISO=board.MISO)
@@ -17,12 +19,13 @@
 
 # give them all to our driver
 print("Creating display")
-#display = Adafruit_SSD1608(200, 200, spi,         # 1.54" HD mono display
-#display = Adafruit_IL91874(176, 264, spi,         # 2.7" Tri-color display
+#display = Adafruit_SSD1608(200, 200, spi,        # 1.54" HD mono display
+#display = Adafruit_SSD1675(122, 250, spi,        # 2.13" HD mono display
+#display = Adafruit_IL91874(176, 264, spi,        # 2.7" Tri-color display
 #display = Adafruit_IL0373(152, 152, spi,         # 1.54" Tri-color display
-#display = Adafruit_IL0373(128, 296, spi,          # 2.9" Tri-color display
-#display = Adafruit_IL0398(400, 300, spi,          # 4.2" Tri-color display
-display = Adafruit_IL0373(104, 212, spi,         # 2.13" Tri-color display
+#display = Adafruit_IL0373(128, 296, spi,         # 2.9" Tri-color display
+#display = Adafruit_IL0398(400, 300, spi,         # 4.2" Tri-color display
+display = Adafruit_IL0373(104, 212, spi,          # 2.13" Tri-color display
                           cs_pin=ecs, dc_pin=dc, sramcs_pin=srcs,
                           rst_pin=rst, busy_pin=busy)
 
diff --git a/examples/epd_blinka.py b/examples/epd_blinka.py
index 8b9b57a..163335b 100644
--- a/examples/epd_blinka.py
+++ b/examples/epd_blinka.py
@@ -6,25 +6,42 @@
 from PIL import ImageDraw
 from PIL import ImageFont
 from adafruit_epd.epd import Adafruit_EPD
-from adafruit_epd.il0373 import Adafruit_IL0373
+from adafruit_epd.il0373 import Adafruit_IL0373      # pylint: disable=unused-import
+from adafruit_epd.il91874 import Adafruit_IL91874    # pylint: disable=unused-import
+from adafruit_epd.il0398 import Adafruit_IL0398      # pylint: disable=unused-import
+from adafruit_epd.ssd1608 import Adafruit_SSD1608    # pylint: disable=unused-import
+from adafruit_epd.ssd1675 import Adafruit_SSD1675    # pylint: disable=unused-import
+from adafruit_epd.ssd1675b import Adafruit_SSD1675B  # pylint: disable=unused-import
+from adafruit_epd.ssd1681 import Adafruit_SSD1681    # pylint: disable=unused-import
 
 # create the spi device and pins we will need
 spi = busio.SPI(board.SCK, MOSI=board.MOSI, MISO=board.MISO)
 
-ecs = digitalio.DigitalInOut(board.D22)
-dc = digitalio.DigitalInOut(board.D13)
-srcs = digitalio.DigitalInOut(board.D6)
-rst = digitalio.DigitalInOut(board.D19)
-busy = digitalio.DigitalInOut(board.D26)
+# create the spi device and pins we will need
+spi = busio.SPI(board.SCK, MOSI=board.MOSI, MISO=board.MISO)
+ecs = digitalio.DigitalInOut(board.D4)
+dc = digitalio.DigitalInOut(board.D5)
+srcs = None
+rst = digitalio.DigitalInOut(board.D6)    # can be None to not use this pin
+busy = digitalio.DigitalInOut(board.D7)    # can be None to not use this pin
+
 
 
 # give them all to our driver
 print("Creating display")
-display = Adafruit_IL0373(104, 212, spi,
-                          cs_pin=ecs, dc_pin=dc, sramcs_pin=srcs,
-                          rst_pin=rst, busy_pin=busy)
-
-
+#display =  Adafruit_SSD1608(200, 200, spi,        # 1.54" HD mono display
+#display =  Adafruit_SSD1681(200, 200, spi,        # 1.54" HD mono display (alt)
+#display =  Adafruit_SSD1675(122, 250, spi,        # 2.13" HD mono display
+#display = Adafruit_IL91874(176, 264, spi,        # 2.7" Tri-color display
+#display =  Adafruit_IL0373(152, 152, spi,         # 1.54" Tri-color display
+#display =  Adafruit_IL0373(128, 296, spi,         # 2.9" Tri-color display
+#display =  Adafruit_IL0398(400, 300, spi,         # 4.2" Tri-color display
+#display =  Adafruit_IL0373(104, 212, spi,          # 2.13" Tri-color display
+display = Adafruit_SSD1675B(122, 250, spi,       # 2.13" HD mono display (rev B)
+                            cs_pin=ecs, dc_pin=dc, sramcs_pin=srcs,
+                            rst_pin=rst, busy_pin=busy)
+
+display.rotation = 3
 # Create blank image for drawing.
 # Make sure to create image with mode '1' for 1-bit color.
 width = display.width
@@ -40,13 +57,15 @@
 
 # Get drawing object to draw on image.
 draw = ImageDraw.Draw(image)
+# empty it
+draw.rectangle((0, 0, width, height), fill=WHITE)
 
-# Draw a white filled box to clear the image.
-draw.rectangle((0,0,width,height), outline=BLACK, fill=WHITE)
+# Draw an outline box
+draw.rectangle((1, 1, width-2, height-2), outline=BLACK, fill=WHITE)
 
 # Draw some shapes.
 # First define some constants to allow easy resizing of shapes.
-padding = 2
+padding = 5
 shape_width = 30
 top = padding
 bottom = height-padding
@@ -68,7 +87,7 @@
 x += shape_width+padding
 
 # Load default font.
-font = ImageFont.load_default()
+font = ImageFont.truetype('/usr/share/fonts/truetype/dejavu/DejaVuSans.ttf', 20)
 
 # Alternatively load a TTF font.  Make sure the .ttf font
 # file is in the same directory as the python script!
diff --git a/examples/epd_bonnet.py b/examples/epd_bonnet.py
new file mode 100644
index 0000000..b64d179
--- /dev/null
+++ b/examples/epd_bonnet.py
@@ -0,0 +1,100 @@
+import time
+import busio
+import board
+from digitalio import DigitalInOut, Direction
+
+from PIL import Image
+from PIL import ImageDraw
+from PIL import ImageFont
+from adafruit_epd.epd import Adafruit_EPD
+from adafruit_epd.ssd1675b import Adafruit_SSD1675B  # pylint: disable=unused-import
+
+# create two buttons
+switch1 = DigitalInOut(board.D6)
+switch2 = DigitalInOut(board.D5)
+switch1.direction = Direction.INPUT
+switch2.direction = Direction.INPUT
+
+# create the spi device and pins we will need
+spi = busio.SPI(board.SCK, MOSI=board.MOSI, MISO=board.MISO)
+ecs = DigitalInOut(board.D8)
+dc = DigitalInOut(board.D22)
+rst = DigitalInOut(board.D27)
+busy = DigitalInOut(board.D17)
+
+# give them all to our driver
+display = Adafruit_SSD1675B(122, 250, spi,       # 2.13" HD mono display (rev B)
+                            cs_pin=ecs, dc_pin=dc, sramcs_pin=None,
+                            rst_pin=rst, busy_pin=busy)
+display.rotation = 1
+
+# Create blank image for drawing.
+# Make sure to create image with mode '1' for 1-bit color.
+width = display.width
+height = display.height
+image = Image.new('RGB', (width, height))
+
+WHITE = (0xFF, 0xFF, 0xFF)
+BLACK = (0x00, 0x00, 0x00)
+
+# clear the buffer
+display.fill(Adafruit_EPD.WHITE)
+# clear it out
+display.display()
+
+# Get drawing object to draw on image.
+draw = ImageDraw.Draw(image)
+# empty it
+draw.rectangle((0, 0, width, height), fill=WHITE)
+
+# Draw an outline box
+draw.rectangle((1, 1, width-2, height-2), outline=BLACK, fill=WHITE)
+# Draw some shapes.
+# First define some constants to allow easy resizing of shapes.
+padding = 5
+shape_width = 30
+top = padding
+bottom = height-padding
+# Move left to right keeping track of the current x position for drawing shapes.
+x = padding
+# Draw an ellipse.
+draw.ellipse((x, top , x+shape_width, bottom), outline=BLACK, fill=WHITE)
+x += shape_width+padding
+# Draw a rectangle.
+draw.rectangle((x, top, x+shape_width, bottom), outline=WHITE, fill=BLACK)
+x += shape_width+padding
+# Draw a triangle.
+draw.polygon([(x, bottom), (x+shape_width/2, top), (x+shape_width, bottom)],
+             outline=BLACK, fill=WHITE)
+x += shape_width+padding
+# Draw an X.
+draw.line((x, bottom, x+shape_width, top), fill=BLACK)
+draw.line((x, top, x+shape_width, bottom), fill=BLACK)
+x += shape_width+padding
+
+# Load default font.
+font = ImageFont.truetype('/usr/share/fonts/truetype/dejavu/DejaVuSans.ttf', 20)
+
+# Alternatively load a TTF font.  Make sure the .ttf font
+# file is in the same directory as the python script!
+# Some other nice fonts to try: http://www.dafont.com/bitmap.php
+#font = ImageFont.truetype('Minecraftia.ttf', 8)
+
+# Write two lines of text.
+draw.text((x, top),    'Hello',  font=font, fill=BLACK)
+draw.text((x, top+20), 'World!', font=font, fill=BLACK)
+
+while True:
+    if not switch1.value:
+        print("Switch 1")
+        display.image(image)
+        display.display()
+        while not switch1.value:
+            time.sleep(0.01)
+    if not switch2.value:
+        print("Switch 2")
+        display.fill(Adafruit_EPD.WHITE)
+        display.display()
+        while not switch2.value:
+            time.sleep(0.01)
+    time.sleep(0.01)
diff --git a/examples/epd_simpletest.py b/examples/epd_simpletest.py
index 858704a..2f6052d 100644
--- a/examples/epd_simpletest.py
+++ b/examples/epd_simpletest.py
@@ -19,7 +19,7 @@
 # give them all to our driver
 print("Creating display")
 #display = Adafruit_SSD1608(200, 200, spi,        # 1.54" HD mono display
-#display = Adafruit_SSD1675(250, 122, spi,        # 2.13" HD mono display
+#display = Adafruit_SSD1675(122, 250, spi,        # 2.13" HD mono display
 #display = Adafruit_IL91874(176, 264, spi,        # 2.7" Tri-color display
 #display = Adafruit_IL0373(152, 152, spi,         # 1.54" Tri-color display
 #display = Adafruit_IL0373(128, 296, spi,         # 2.9" Tri-color display